New Materials and Advanced Materials
Heftet /
2011
/ Engelsk
Produktdetaljer
ISBN
9780878492039
Publisert
2011-01-31
Utgiver
Trans Tech Publications Ltd; Trans Tech Publications Ltd
Vekt
3700 gr
Høyde
240 mm
Bredde
170 mm
Dybde
100 mm
Aldersnivå
P, 06
Språk
Product language
Engelsk
Format
Product format
Heftet
Antall sider
1994
Volume is indexed by Thomson Reuters CPCI-S (WoS).
These 379 peer-reviewed papers, presented in a two-volume set, cover the latest advances in nanocrystalline materials, thin films and chemical vapor deposition, biocomposites, ceramics technology, MEMS, coatings, nanopowders, fuel cells, etc.; together with their practical application.
Les mer
<p>Selected, peer reviewed papers from the 2010 International Conference on Advances in Materials and Manufacturing Processes (ICAMMP 2010), 6-8 November, 2010, Shenzhen, China</p>
- Sponsors, Committees and Preface
- Recycled Concrete Using Crushed Construction Waste Bricks Subject to Elevated Temperatures
- Volume Fraction Effects of Silicon Carbide on the Wear Behavior of SiCp-Reinforced Magnesium Matrix Composites
- Electrical Conductivity and Density of the Molten CaCl2-NaCl-Al2O3 Electrolyte Materials
- Characterization of (Al2O3)p/Al Composites In Situ Synthesized by Direct Melt Reaction Method
- Study on Lamellar Precipitates of the Austenitic Valve Steel
- Analysis on Chaotic Behavior in Rock Damage Rheological Process under Uniaxial Stress
- Detection of Kaiser Effect in Marbles under Brazilian Tests
- Preparation and Characterization of Modified PVDF-g-PSSA Membrane
- Influences of Micro-Arc Oxidation on Pre-Corroded Fatigue Property of Magnesium Alloy AZ91D
- Study on Range of the Sampling Period of the Electro-Hydraulic Position Sampling Control System Based on PLC
- In Air Template-Free Synthesis of In2S3 Hierarchical Nanostructure from InCl3·4H2O and Thiourea
- Preparation, Characterization, and Surface-Enhanced Raman Spectroscopy Activity of Spherical α-Fe2O3/Ag Core/Shell Nanoparticles
- Damage Progress Simulation in Unidirectional Composites by Extended Finite Element Method (XFEM)
- Quality Determination of Glass/Epoxy Prepreg by NIR Spectroscopy
- Multiferroic Bismuth Ferrite Nanoparticles: Rapid Sintering Synthesis, Characterization, and Optical Properties
- Investigation for Test Sensitivity of Shearography
- Design of New Environment-Friendly Friction Material and Optimization of the Ratio Method
- Preparation of Highly Pure Nano-Silver Colloids Modified by Polyethylene Glycol
- The Optimization of the Technologic Parameter in Strong Cooling with Single-Tube on the A356 Alloy
- Effect of Friction Temperature on Spheroidization and Refinement of Si Particles in Hypereutectic Al-Si Alloys
- Flame Retardant Composites of Rare Earth Oxides/ Conventional Flame Retardants/ Silicone Rubber with Good Self-Extinguishing
- Green's Function Approach to Crossover Properties for Interaction Parameters of an N-Layer Ferroelectric Thin Film
- Preparation and Characterization of BaFe12O19 Hollow Nanocrystalline Aggregations
- Structure and Performance of 35 Steel after Strengthened Shot Peening Surface Nanocrystallization and Gas Tufftriding Process
- Absorptive and Biodegraded Polyurethane Foamed Urea
- Study on Photodynamic Therapy for HL60 Cells Inactivation by Visible Light-Induced Fe-Doped Nano-TiO2 under Magnetic Field
- Two Nickel-Bipyridinedicarboxylate Organic-Inorganic Hybrid Materials: Hydrothermal Synthesis, Crystal Structure and Thermal Properties
- Performance of the Self-Breathing Air Direct Methanol Fuel Cell with Modified Poly (Vinylidene Fluoride) Grafted onto a Blended Polystyrene Sulfonated Acid (m-PVDF-g-PSSA) Membranes
- Effect of Temperature and Inoculation on Structure Property of Chilled Cast Iron Camshaft
- Experiment Analysis on Transient Braking Factor of Drum Brake
- Studies on Related ms Magnitude Rate Models in Triangular Wave Unloading Section of Calcium Medium-Fine Sandstone
- Numerical Simulation of Mixed-Mode Crack Induced Failure of Steel Plate Strengthened Concrete Beam
- Research on Anti-Friction Mechanism of Ni60A/MoS2 Composite Coating
- Numerical Simulation of the Reflective Crack Propagation Path for Open-Graded Large Stone Asphalt Mixes
- Thermal Decomposition Kinetic and Electrochemical Properties of KZn2(PO4)(HPO4)
- Design and Implementation of Electric Vehicle Power Lithium Battery Protection Board
- Microstructure and Mechanical Properties of Magnesium Alloy AZ81 with Yttrium
- Titania-Phosphotungstic Acid Nanocomposites Dispersed Homogeneously in Mesopores as the Recyclable Photocatalyst
- Fluorescence Enhanced Quantum Dots: Its Synthesis, Optical Properties, and Ecotoxicity Research
- Effects of Ultra-Fine Limestone Powder on Workability and Strength of High Strength Concrete
- Influence of Substrate Temperature on Structure and Optical Property of Cu3N Thin Films
- Thermal Degradation of Hydroxyl-Terminated Poly(L-Lactic Acid) Oligomer into L-Lactide
- Effect of Temperature on Structure and Corrosion Resistance of Oxide Scale on Hot Rolled Strip
- An Experimental Study of Bipolar Pulse Electroforming Nickel
- The Study of Liquid-Liquid Structural Transition of PbSnBi Ternary Alloy
- Crack Healing Behavior of 12%Cr Ultra-Super-Critical Rotor Steel
- Experimental Research on Bending Behavior of 2.5D Woven Fabrics
- Microstructures and Properties of Bainitic Nodular Cast Iron Treated by Controlled Cooling and Austempering Treatment
- Error Model and Simulation to Arbitrary Point of Automobile Panels in Normal Mechanical Parameter Measurement Instrument
- Effective Thermal Conductivity of Composites with Different Particle Geometries and Interfacial Thermal Resistance
- Study on Structure and Magnetization of Spinel Ferrites
- Element Selection and Meshing in Finite Element Contact Analysis
- Characterization and Thermal Behaviour of Polymer-Dispersed Liquid Crystals
- Experimental Study on Polyphosphoric Acid (PPA) Modified Asphalt Binders
- Effects of Ultra-Fine Limestone Powder (LP) and Fly Ash Complex Adding on the Workability and Strength of Concrete
- Development on Microalloyed High Carbon Steel Used for Fracture Splitting Connecting Rods
- Preparation of Carbon-Coated Nano-Fe, Co Particles and their Effects on the Thermal Decomposition of Ammonium Perchlorate
- Immobilization of Radioactive Wastes into CaTiO3 Synroc by the SHS Method
- Boron and Phosphorus Segregation Behavior at Grain Boundary in a Ti-If Steel after Annealing
- Preparation and Properties of Nylon Composite Powder by Selective Laser Sintering
- Effect of Heating Temperature of Quenching on the Properties of TiCp/Fe Composite
- Integrated Innovative Technology for Micro-Manufacturing Based on Precision Cutting and Thin Films Deposition
- Kinematics and Trajectory Tracking Motion Plan of an Unmanned Bicycle
- Cutting Line Design Method for Woven Composite Materials Fitting to Free Surface
- Corrosion Inhibition Mechanism of Magnetic Field on Carbon Steel
- Parameter Simulation for Quenching and Pre-Stretching about Aluminum Alloy Thick Plates Based on MARC Finite Element
- Chloride Binding of Cementitious Pastes
- Research about Online Inspection System for the Assembly Quality of Automobile Gearbox Sliding Bracket
- Preparation of Low Chlorine Shellac by Catalytic Hydrogenation with Pd/C
- Study on Bio-Hydrogen Production of Different Fermentation Types
- Feature Extraction of Machine Vibration Using Lifting Wavelet Denoising and EMD and its Application in Fault Diagnosis
- Effect of Volume Fraction of NiMnGa Powders on Magnetic-Field-Induced Strain in NiMnGa/Polymer Composites
- Photodegradation of Ammonia by TiO2 Nanoparticles Produced by Flame CVD Process
- Thermal Insulation Behaviors of Rinforced Concrete Composite Wall with Inner Insulating Layer
- Recent Advances in the Bioactivities and Structural Analysis of Chondroitin Sulfate
- Phase Transformation and Properties under Different Quenching Mediums of a X120 Pipeline Steel
- The Microstructure and Enhanced Field Electron Emission Properties of Boron-Doped Nanocrystalline Diamond Films by Microwave Plasma Chemical Vapor Deposition
- Numerical Simulation in Soft Argillaceous Shale Geo-Material Based on Porous Elasto-Plastic Model
- Application of Calculus Equation in Solving Thermal Decomposition Kinetics Parameters of Fire-Retardant Foam
- A Novel Method for Estimating State of Charge of Lithium Ion Battery Packs
- On Preparation of In Situ Composite Steel with Ultra-High Strength and its Thermal Stability
- Visible-Light Activity Evaluation of p-n Junction Photocatalyst NiO/TiO2 Prepared by Sol-Gel Method
- Effects of Nano-ZnO Power-Coated PVC Film on the Physiological Properties and Microbiological Changes of Fresh-Cut "Fuji" Apple
- Spline Subdomain Approach to Thermal Conduction Problem for Composite with Rectangular Shape Particle
- Experimental Study on the Stitching Reinforcement of Composite Member with a Circular Hole
- Study on Preparation and Properties of Nano-Modified Polypropylene
- Synthesis, Characterization and Application Polystyrene-Bound Manganese Complexes
- Repellent Effects of the Insecticide Based on Porous Starch and Fennel Essential Oil against Tribolium confusum
- Effect of Soft Foamed Polyethylene on the Property of Portable Mini-Cold Storage
- Pb (II)-Imprinted Chitosan/TiO2 Hybrid Film for High Selectivity of Adsorption Lead Ion in Aqueous Solution
- Development of Nano-ZnO Coated Food Packaging Film and its Inhibitory Effect on Escherichia coli In Vitro and in Actual Tests
- The Kelvin Probe Study on Initial Corrosion of Weathering Steel with NaCl Deposition
- Preparation and Characterization of Si3N4/TiCN Composite Ceramic Tool Material
- Thermal Stability of Cotton Cellulose Modified with Flame Retardants
- Characteristics and Release Behavior of Sodium Alginate Microencapsulation Containing Cinnamon Oil
- The Effect of Formulation Variables on the Encapsulation Efficiency and SO2-Release Behavior of Microparticles Containing Sulphite
- Analysis of Failure of 316L Heat Exchanger in a Producing Glycine Process Using Hydantoin Method
- Simulation Experiment Research on the FRP Bolt under Eccentric Load
- Synthesis, Characterization and Mechanical Properties of Hydroxyl-Terminated Hyperbranched Polymer Graft Polyether-Based Aliphatic Polyurethane Elastomer
- Smart Materials of Cured Epoxy Polymer Modified by 6F-PEEK with Shape Memory Effect
- Simulation of Size Effects in Material with Growth Twins
- Forming Limit Diagram of Stainless Steel-Aluminum Alloy Clad
- Microstructure and Mechanical Properties of Fly Ash Al-25Mg Composites Processed by Powder Metallurgy Method
- Effect of Heat Treatment on Anticorrosion of Soft Magnetic Alloy Fe81Cr17Si1.5TiBRe
- Influence of Metal Cations on the Structure and Release Property of Layered Double Hydroxide-Ibuprofen Host-Guest Materials
- Influence of Aging on Microstructure and Mechanical Properties of Wrought Magnesium Alloys
- Atomic Force Microscopy and X-Ray Photoelectron Spectroscopy Study on the Surface and Interface States of Liq and ITO Films
- Preparation on Low-Temperature Resistance Nitrile-Butadiene Rubber Coat-Metal Sealing Gasket
- Tribological Properties of Pb-Sn-CNTs Composite Coatings
- Magnetic Induction Effect of Amorphous Ribbon Modified by Rare-Earth
- A Meso-Scale Simulation on the Effects of Temperature and Strain Rate on the Tensile Mechanical Behavior of Pure Titanium
- Fabrication and Growth Mechanism of Star-Shaped Gold Nanoparticles via Seed-Mediated Growth Method
- Improved Computation Formula of Thermal Conductivity of Fibrous Porous Materials
- The Operation Characteristics of Biohydrogen Production in Continuous Stirred Tank Reactor with Molasses
- Thickening Mechanism of Crystalline Polyester Involved in Low Pressure Sheet Molding Compounds
- Galvanneal Coating of Galvannealed Steel Sheet Fracture Research by Dynamic Tensility
- Effects of SiC Particle and Holding Time on Semi-Solid Microstructure of SiCP/AZ61 Composites
- Precipitate Structure in an Alumina Dispersion-Strengthened Copper Base Composite Layer
- Electrokinetic Phenomena of Sulfonated-Polyethersulfone Ultrafiltration Membrane Modified by TiO2 Nanoparticles
- Phase Evolution and Formation Mechanism in Acicular Mullite Prepared from Kaolinite via Wet Chemistry Method
- Preparation of Nano-Al2O3-Coated ZrO2 Modified by Silane Coupling Agent
- The Effect of Hydrothermal Treatment on the Micromorphology of Aluminum Sulfate Hydrolysis Product
- Research of G105 Chloride Ion Stress Corrosion Cracking
- Studies on a New Type of Crosslinked Polyacrylamide Bentonite Composite
- Preparation and Characterization of Nanometer Calcium Titanate Immobilized on Aluminum Oxide and its Adsorption Capacity for Heavy Metal Ions in Water
- Synthesis and Characterization of Nanocrystalline ZnO Powders by a Novel Combustion Synthesis Method
- Measurement and Correlation for Solubility of D-Glucurono-1,4-Lactone
- Effects of Calcining Conditions on the Structures of Co-Doped VO2(M) Nanopowders
- Improve the Efficiency of White Organic Light-Emitting Devices Using Double-Doped System
- Adsorption of Methylene Blue from Aqueous Solution onto Peracetic Acid-Modified Loosestrife Powder - A New Adsorbent
- Photoluminescence and Structural Characteristics of SnO2 Nanopetals Synthesized by Thermal Evaporation
- Characteristics of Biohydrogen Production by Ethanoligenens Sp. R3 Isolated from Continuous Stirred Tank Reactor
- Beneficial Use of Fly Ash in Concrete Incorporating PCA
- Experimental Researches on Detonation of Aluminized Explosives to High-Speed Flyer Impact
- Research on Eccentricity Magnification Factor of Eccentric Compression Lightweight Aggregate Concrete Member
- Preparation and Characterisation of an Aligned Carbon Nanotube Array on the Ni-Deposited Silicon Surface
- Semi-Solid Deformation of Al-Fe Alloy Prepared by Electromagnetic Stirring
- Preparation and Research of Tussah Silk Fibroin/Hydroxyapatite Composites
- The Effects of the TiO2 Films Thickness on the Performance of Quasi-Solid Dye-Sensitized Solar Cells
- Study on the Precipitated Behavior and Stability of the Strengthening Phase Al12(Fe,X)3Si in Al-Fe-Si-X Alloys with the EET Theory
- An Improved Method for the Synthesis of SAPO-41
- Effect of Anneal Time on Photoelectric Properties of SnS:Ag Thin Films
- Research of Environmental Factors of Aluminum Alloys Atmospheric Corrosion Based on Grey Relational Analysis
- Characterization of ZnO Nano-Coatings on Fibreboard
- Integration of CuO Thin Film and Bi2Te3 for Enhancing the Thermoelectric Conversion Efficiency of Thermoelectric Generator
- A Micromechanical Model for Deformation Behavior of Nanocrystalline Copper
- Genetic-Fuzzy Optimal Design of Straw Crusher Based on Full-Feeding Combine Harvesters
- Measuring and Modeling of Viscosities of Selected CaO-MgO-Al2O3-SiO2 Slags
- Adsorption of Phthalate Esters (PAEs) from Aqueous Solution onto Activated Carbons from Softstem Bulrush
- Preparation and Characterization of SiO2/VO2 Composite Particles
- Phase Evolution and Microwave Dielectric Properites in the Systems of (Mg1-xCax)2SiO4 Ceramics
- Thermal Shock Stability of Large Size ZrB2 Ceramic Matrix Composite Material
- Technique Based on an Innovative Design of CNC Turning Center
- Study on Microstructure Characterization of Al-N Codoping ZnO Films and Doping Mechanism
- Steam Reforming of Simulated Coke Oven Gas over Ni/Al2O3-MgO Catalysts for Syngas Production
- The Application of Calcium Sulfate Whisker in Styrene-Acrylic Emulsions
- Preparation and Characterization of Marble/Unsaturated Polyester Resin Composite Materials
- Effect of Thermal-Oxidative Aging on the Mechanical Properties of Carbon Fiber Reinforced Bis-Maleimide Composites
- Research on Removal of Sulfide Inclusion in Steel Surface by Molten Salt Electrolysis
- The I-V Characteristics of the 3,3',5',5-Tetra-Tert-Butyl-Azobenzene Optical Molecular Switch: A First-Principles Study
- Thermal-Mechanical Analysis for Surface Cracks on FTSC Slab
- Preparation and Characterization of CuO-Doped ZnO
- EBSD Analysis of HAZ Microstructure Characteristics of a High Strength Low Welding Crack Susceptibility Steel
- Preparation and Investigation of Hydrophobic Mesoporous Silica Films
- Catalytic Reforming of Model Tar Compounds from Hot Coke Oven Gas for Light Fuel Gases Production over Bimetallic Catalysts
- Solute Pre-Precipitation and Phase Transformation in a Mg-Zn-Gd Alloy
- Studying on Preparation of AZO Thin Films with Sol-Gel Method
- Investigation on Generation Performance for Tubular Direct Methanol Fuel Cell
- Determination of Thickness for the Individual Layer of Strained P-Type Al0.11Ga0.89NGaN Superlattice by High Angle Annular Dark Field Scanning Transmission Electron Microscopy
- Wear Properties of Reaction Sintered B4C Composites
- Vibration Emulating and Measuring of Pipe System Being Filled with Liquid Ammonia in Chemical Ship
- Test on the Mortar Mix Ratio with Aeolian Sand of Mu Us Desert
- SEM Analysis of Non-Conducting Materials under Low Vacuum Conditions
- Effect of Various Pretreatment Methods of Inoculum on Biohydrogen Production
- Prepared of Flower-Like CuO via CTAB-Assisted Hydrothermal Method
- Morphology of the Diamond Thin Films Grown by Microwave Plasma Chemical Vapor Deposition with Different Aftertreatments
- Optically Active Films Fabricated from Poly(Allylamine Hydrochloride) and R-(+)-1-Phenylethylamine Derivatives of Poly(Ethylene-Alt-Maleic Acid) with Different Degrees of Substitution
- Thermal Property, Morphology, Mechanical and Rheological Properties of a Modified Bio-Polymers Prepared by Blending Poly(3-Hydrobutyrate-Co-4-Hydrobutyrate) with Chain Extenders
- An Ab Initio Study on Negative Differential Resistance in Pyrrole Trimer Molecular Device
- Preparation and Characterization of Modified Activated Carbon and its Influencing Factors of Cd2+ Adsorption
- Oxidation Behavior of TiAl Based Alloys Prepared by Spark Plasma Sintering
- Behavior of Phosphorus Adsorption from Aqueous Solutions on Modified Activated Alumina
- A Novel Structure Design of Conductive and Magnetic Electromagnetic Shielding Composites
- Research on Optimization Design of the Lateral Stiffness Satio about the Frame-Supported Multi-Ribbed Structure
- Protection Capability of Different Confinement Plates for Rubber Composite Armours against Shaped Charges
- Preparation, Characterization and Magnetic Properties of Fe59Co41 Alloy Nanowires Using AC Electrochemical Deposition
- Effects of Salt Corrosion and Freeze-Thaw Cycle on Rubberized Cement-Soil
- VOCs Decomposition Using Multiple Catalysis in Non-Thermal Plasma Processing
- Development and Characteristic of Bacterial Cellulose for Antimicrobial Wound Dressing
- Dynamic Compressive Response and Failure Behaviour of CFRP Composites at High Strain Rates
- Experimental Study on Performance of Green Complex Binder of Low-Grade Fly Ash and Limestone Powder
- Experiment on C40 Machine-Made Sand Concrete with Combined Admixture of Limestone Powder and Substandard Fly Ash
- Preparation and Characterization of MgCr2O4 Nanocrystals by Microwave Method
- Ductile Damage Evolution Analysis of Lead-Free Sn-Zn Solder Based on Meso Topography
- Behavior of Carbide Dissolution and Precipitation in WD1 Steel Used for Warm Work Dies
- Preparation and Characterization of Nanosized Barium-Strontium Titanate Immobilized on Aluminum Oxide and its Application in Separation of Cr(III) and Cr(VI)
- An Analysis of Slope Stability of Sand Embankment with Shear Strength Reduction (SSR) Method
- 2D FE Modeling of Cracked Aluminum Plates Repaired with Adhesively Bonded Composite Patches
- The Preparation of ZnO Gas-Sensing Material by Nucleation-Crystallization Separation Method
- Microstructure and Mechanical Properties of Hot Rolled TRIP Steel Based on Dynamic Transformation of Undercooled Austenite
- Preparation and Characterization of Water Based and Double Enveloped Nano-Fe3O4 Magnetic Fluids
- Relationships between the Abilities of the Forming Bond of the Precipitated Phases and their Precipitations and Phases Transition in Al-Fe-Si Alloy
- Erosion-Abrasion Behavior of Eutectic Al-Mn Alloy Matrix Composites Reinforced with Al2O3 Particulates
- FEM Analysis and Experimental Study for Bond Strength of High-Strength Coating by Wedged Load Test Method
- Effects of Fe2+ on Fermentation and Biohydrogen Production of Biohydrogenbacterium R3 sp.nov.
- Hydrogen Production by Hydrolyzing Zn Nano-Particles in a Cyclone Reactor
- Effect of Minor Sc, Zr and Ti Additions on the Microstructures and the Mechanical Properties of Pure Aluminium
- Research on Microstructure and Oxidation Resistance of Double Glow Plasma Discharge Surface Titanizing on CrZrCu Alloy
- Effects of Yttrium on Microstructure and Mechanical Properties of In Situ (Al2O3+Al3Zr)p/A356 Composites
- Simulation on Displacement Characteristics of Variable Displacement of Double-Action Vane Pump
- Study and Design of Sheet Metal Bending Springback Adjustable Die
- Ab Initio Investigations of Electronic Structure and Optical Properties of Ag-F Codoped ZnO
- The Influence of pH Values on Corrosion Properties of 316L Stainless Steel in Simulated Circulating Cooling Water
- Photocatalytic Activity of TiO2-NaY Composite Photocatalyst on Methyl Orange Degradation
- The Influence of Particle Size, Concentration of Electrorheological Fluid on the Properties and Morphology of ER
- The Stress Concentration Factor of Different Corrosion Pits Shape
- Numerical Simulation of Forming Force in Lateral Bend Forming
- Crack Pattern of SRUHSC Column and SRC Beam Joint Subjected to Reversal Cycle Load
- TiO2 and 5A Zeolite Composite Prepared for Photocatalytic Methyl Orange Degradation
- Research on Surface Modified Micro/Nano-MgO Particles Improve Tribological Characteristics of Lubricating Oil
- The Coal Oxidized by HNO3 on the Conductivity Effect of Coal-Based Polyaniline
- Methods to Make Silicon and Silica Luminescent
- Preparation of C/SiC Composites by SLA-Intergrated Liquid Silicon Infiltration Method
- Study on the Relationship between Microscopic Structure and Mechanical Properties of HTPB Propellant
- 3D Braided Geometry Structures Based on Space Group
- Electrochemical Compatibility between Natural Graphite and Li6BaLa2Ta2O12 or Organic Electrolytes
- Characters of Expressway Widened Engineering Reinforced with Geotextile
- Expandable Tubing R&D on the Material of FMA Multiphase Alloy Steel
- Drying Shrinkage of Concrete Affected by Content of Stone Powder in Proto-Machine-Made Sand
- Molecular Dynamics Simulations of Uniaxial Compression of Ceria and Gadolinia Doped Ceria
- The Performance of Barium Sulfate/Nature Rubber Composites Using in Sport Shoes
- Microcosmic Deform Incoordination and the Law of Limiting Strength Release during Shearing Failure of Concrete
- Mechanism Analysis of Rutting at Urban Intersections Based on Numerical Simulation of Moving Loads
- A ZnO/Chitosan Composite Film: Fabrication and Anticorrosion Characterization
- A New Method for Manufacturing Composite Ingot of 3004/4045 Aluminum Alloy
- Design and Implementation of BMS Based on STC12C5A60S2
- A Statistical Constitutive Model for the Strength of Brittle Fiber at Different Strain Rates
- Experimental Investigation of Microsegregation in Low Frequency Electromagnetic Casting of Al-4.5%Cu Binary Alloy
- Hydrothermal Synthesis and Characterization of Single-Crystal Lead Titanate Nanoflakes
- Mechanical Wear of SnO2-C Morph-Genetic Composite Materials
- Preparation and Characterization of Shellac Fiber as a Novel Material for Controlled Drug Release
- Synthesis of Star-Shaped PLA via Direct Melt Polycondensation: 1. Using L-LA as Starting Material
- The Effect of Melt-Spinning Technology on the Degradation of Poly(Glycolic Acid) Fiber In Vitro
- The Fracture Research of Hexagonal Duralumin Nut
- Influence of Citric Acid on the Formation of Hydroxyapatite Powders by Using Ca(NO3)2-P2O5 Ethanol Solution System
- Effect of Heat and Wet Treatment on the Strength of PLA Fiber
- Application of a Coating Sensor to Aluminum Structural Crack Monitoring
- The Research on Anti-Corrosion Property of Epoxy/Polyurethane Coating of Magnesium Alloys
- Controllable Preparation of Multi-Morphology Nanosized Silica by Hydrolysis of Mixed Chlorosilanes in Mixed Solvent of Alcohol and Water
- Experimental Study of Rolling Contact Fatigue Life of Zirconia Ceramic Ball
- Effect of Tempering on Microstructure and Mechanical Properties of Ultra Low Carbon Heavy Steel Plate with Intercritical Quenching
- Effects of Heating Period of Time on Tensile Property of Three-Dimension and Five-Direction Braided/Epoxy Resin Composites at High Temperature
- Analysis of Influence Rules of Material Composition on Compaction Characteristic of Asphalt Mixtures Using SGC Tests
- Simulation and Microstructure Predict during Hot Die-Forging of Cast Mg-7.0Al-0.2Zn Magnesium Alloy
- Study on the Relationship between Transparency and Morphology of Shoushan Stone
- Synthesis of Star-Shaped PLA via Direct Melt Polycondensation: 2. Using D,L-LA as Starting Material
- Synthesis and Characterization of Fluorine-Substituted Hydroxyapatite Powder by Polyacrylamide-Gel Method
- Families of Exact Solutions for Two-Component Bose-Einstein Condensates
- Mechanical Properties of Bulk Nanocrystalline Silver-Using Compression Tests
- Design on Operating Conditions Date Acquisition and Remote Transmission System for Electric Vehicle
- Study on Preparation of Activated Carbon from Corncob Furfural Residue with ZnCl2 by Microwave Irradiation
- Influences of Complex Modification of RE and P on the Microstructure and Impact Toughness of Hypereutectic Al-24Si Alloy
- Electrospun Antibacterial Chitosan/Poly (Vinyl Alcohol) Nanofibers Containing Silver Nanoparticles
- Synthesis and Properties of N,N-Dimethyl-O-Quaternary Ammonium Chitosan
- Preparation of High-Porosity NiTi Alloys by Powder Sintering with NaCl Pre-Forming
- Analysis of Knuckle Arm's Fatigue Life
- Antibacterial Property and Mechanism of Copper Alginate Fiber
- Preparation of Chitosan/Cyclodextrin/Trisodium Citrate Nanoparticles for the Poor-Water Drug Carrier Material
- The Influence of Electroless-Silver Coated Cenosphere Powders on the Electromagnetic Shielding Interference Effectiveness and Mechanical Properties of the Silicone Rubber
- The Influenceof Rare Earth Element on α-Solidification of A356 Alloy
- Effect of Intercritical Quenching on Microstructure and Mechanical Properties of Ultra Low Carbon Heavy Steel Plate
- Study on the Supramolecular Interaction of Curcumin and RM-β-CD-m
- Effect of Niobium on the Microstructure and Mechanical Properties of Low Carbon Steel Plate with Intercritical Quenching
- Effect of Combined Electromagnetic Field on Microstructure and Surface Quality of (Al2O3+Al3Zr)P/Al Composites
- Effect of La2O3 on the Microstructure and Electrical Properties of (Ti,Sn)O2 Varistor Ceramics
- Effect of Cr Content on Impact and Abrasion Properties and Mechanisms of Low Carbon Alloy Steel at Corrosive Condition
- A Novel Mixed Hydroxide Method for Hydroxyapatite Preparation
- Production of Lactic Acid by Simultaneous Saccharification and Fermentation Using Steam Pretreated Lespedeza Stalks as Inexpensive Raw Materials
- Study on the Forming and Self-Repairing of Ni60A/MoS2 Composite Lubricating Film
- Development of a Novel and Bi-Functional Quantum Dots as FRET Energy Donor
- Electronic Structure and Bonding Characteristic of NdMgNi4H4
- Microstructure and Mechanical Properties of Al-Cu-Mg-Ag Alloy during Thermal Exposed at Elevated Temperature
- In Situ Fabrication and Properties of (Al3Ti)P/6351 Composites
- Micro-Magnetic Field at the Surface of Surgical Materials for Biocompatibility Improvement
- Biomass Biodegradable Food Boxes and Hot Temperature Field of Structural Optimization
- Study on the Thermal Decomposition Behavior of MgAl-Hydrotalcite Compounds
- The Configuration Design and Biodegradation Test of Biodegradable Material Dishware
- Supercritical Solvent Impregnation in Controlled-Release Drugs
- The Influence of Elastic Modulus on the Adhesion of Fouling Organism to Poly(Dimethylsiloxane) (PDMS)
- Rheological Behaviour of Core-Shell Emulsion/Amine Crosslinking Process
- Cytotoxicity and Antiviral Activity of Calcium Alginate Fibers and Zinc Alginate Fibers
- Strength Development of Concrete with Proto-Machine-Made Sand
- A Novel Synthesis of Acetophenone Benzopyran Derivative
- Inclusion Process of Curcuminoid-β-Cyclodextrin Complex and its Stability
- Research and Development of Deep-Sea Pipeline Steel
- Purification and Characterization of a Natural Lectin from the Seed of Peanut Arachis hypogaea
- The Yield Criterion for Processing Bamboo Fiber under Rolling Load
- Toxoplasma gondii DNA Sensor Based on a Novel Ni-Magnetic Sensing Probe
- Controlling the Wall Thickness and Pore Size of SBA-15 by Using PPG and PEG as Additives
- Study on an Air Filter Material Immobilized with Bio-Antimicrobials
- Plasma Treatment on Silk Fibroin Powder/PU Blend Film
- Comparison of Ohmic Contact Characteristics of Different Metal on N Type 4H-SiC
- Synthesis and Application of Polyurethane Hydrogel Carrier on Nitrobacteria Immobilization
- Preparation of Eucommia ulmoides Leaves Antioxidant and its Antioxidation Activity In Vitro
- Fabrication and Characterization of a Toxoplasma gondii DNA Sensing System
- Combined Fireproof and Stuffing Materials Applied to Through-Floor Pipes
- Capacitive Behavior of MnO2 Nanowires Prepared by Hydrothermal Synthesis Method
- The Experiment Study on Making Flame-Retardant by a Brucite in Liaoning Province
- Vacuum Flat Bed Filter Control System for Cold Strip Rolling Mill
- Experimental Study on Frost Resistance Durability of Lightweight Aggregate Concrete in Na2SO4 Solution
- Regeneration of Bagasse Cellulose by Ionic Liquid
- Orthogonal Experimental Study on Frost Resistance of Polypropylene Fiber Concrete
- Study on Thermal Conductivity of Organic Phase-Change Nano-Fluid
- Influence of Ultrafine Limestone Powder on the Performance of High Volume Mineral Admixture Reactive Powder Concrete
- Process of In Situ Cr Oxidation in Cu-Cr Pre-Alloyed Powders
- Study on Phase-Change Temperature and Latent Heat of Organic Phase-Change Nano-Fluid
- Optimization of Machining Parameters on Tool Wear Rate of Ti-6Al-4V through EDM Using Copper Tungsten Electrode: A Statistical Approach
- Morphological Control Synthesis and Characterization of Hydroxyapatite with Star-Shaped
- Investigation on the Diffusion Behavior of Mo-Ni Interface
- Research on Rheological and Thermal Properties of P(3HB-4HB)/PEG and the Preparation for Fiber
- Failure Analysis and Strengthening Method for Circular Diamond Saw Blade
- Preparation of Low Pt-Decorated Ru/C Catalyst and Electrochemical Research
- The Corrosion Behavior about Two Ni-Based Alloys in CO2 / H2S Environments
- First Principles Calculations of Phase Stabilities of YNi2 and YMgNi4
- The Rebinding Properties of Bovine Serum Albumin Imprinted Calcium Phosphate/Polyacrylate/Alginate Hybrid Polymer Microspheres
- Synthesis, Characterization and Properties of Poly(L-Lactic Acid-Co-α- Phenylalanine) Obtained by Direct Melting Copolymerization
- Carbonation of High-Temperature Calcined Hydroxyapatite by Solid-Ion-Exchange Reaction
- Synthesis of Polyvinyl Formal Sponge for Wound Care Dressing Application
- Effects to Active Composition of Tibetan Medicinal Materials with Twinkling Ultrasonic Cavitation
- Synthesis, Characterization and Crystallization of Poly(Ethylene Glycol)-b-Poly(ε-Caprolactone)
- Effects of Various Sugars on the Mineralization of Microbiologically Induced Calcium Carbonate
- Preparation of Biomorphic SiC by Reactive Infiltration of Gaseous Si into Carbonized Millet
- Effects of Fiber Mass Fraction and Alkali Concentration on Mechanical Properties of Biodegradable Composites
- Biomorphic SiC Prepared from Carbonized Millet by Sol-Gel and Carbothermal Reduction Processing
- Forecasting of Cutting Forces in Dental Adjustment of Ceramic Prostheses Using an Artificial Neural Network
- Research on Corrosion Fractal Character of LY12CZ Aluminum Alloy Based on Image Processing Technique
- Study on Band Gap Structure of One Dimensional Phononic Crystals
- Modeling of Drug Release from Matrix Tablets with Process Variables of Microwave-Assisted Modification of Arrowroot Starch Using Artificial Neural Network
- Self-Made Gas Diffusion Electrodes for Dye Wastewater Treatment
- Preparation and In Vitro Evaluation of Carboxymethyl Konjac Glucomannan Coated 5-Aminosalicylic Acid Tablets for Colonic Delivery
- Thermo-Structural Analysis of CLAM Steel and SS316L in the First Wall for ITER during Thermal Cycling
- Finite Element Analysis on Structural Stress of Large Format InSb Infrared Focal Plane Array
- Alginate-Chitosan Microspheres for Controlled Release of Tea Polyphenol
- Study on Glycoprotein in Kiwifruit
- A Novel Scaffold from Recombinant Spider Silk Protein in Tissue Engineering
- Semi-Solid A356 Alloy Slurry Prepared by Slightly Electromagnetic Stirring with Ti-Based Refiner
- Study on the Plasma Beam Surface Remelting Modification of Nodular Cast Iron
- In Situ TEM Observation of Phase Transformation for Bio-Medical Shape Memory TiNbSn Alloy
- Effect of Metal Particles on Spreading Properties of Sn0.7Cu Based Composite Solder
- Bioactive Calcium Phosphate Coating on Carbon/Carbon Composites Prepared by Ultrasonicated Induction Heating Deposition
- Compatibility of L-Tyrosine Derived Biodegradable Polycarbonate/Chitosan Blends
- Preparation of Novel Ag/Bacterial Cellulose Hybrid Nanofibers for Antimicrobial Wound Dressing
- Synthesis and Cure Kinetic Studies of a New Trifunctional Imide Oligomer
- Explore the Effects of Magnetic Field Intensity Change on Acidithiobacillus ferrooxidans Growth and Magnetism
- Extraction and Antioxidant Activity of Collagen from the Chinese Soft-Shelled Turtle (Pelodiscus sinensis)
- The Study of Manufacture of the New Type Coal Ash Ceramsite and Treating Landscape Waste Water with the New Type Coal Ceramsite
- Preparation of Folate Conjugated O-Carboxymethyl Chitosan Nanoparticles
- The Structure of PU/PNIPAAm Semi-IPN Prepared by Wet Phase Inversion Process
- Preparation and Characterization of Silver Powders with Spheric Shape and Different Sizes
- Effect of La Addition on the Microstructures and Mechanical Properties of 7075 Aluminum Alloy
- The Combustion Process and Characteristic Analysis of the Refined Oil-Water Coal Slurry in Diesel Engine
- For Manufacturing and Assembly of the Product Design
- The Atomizing Experimental Study of the Refined Oil-Water Coal Slurry on the Diesel Engine of the Large-Scale Ship
- The Preparation and Temperature Sensitivity of TiCN-Coated Aluminum Foil for Capacitor
- Solvent-Assisted Self-Assembly of ZnO Nanoparticles on Mica and its Characterization
- Calculation Methods on Crack Resistance Capacity of SRUHSC Column to SRC Beam Joint Subjected to Reversal Cycle Load
- The Experimental Research on the New Compound Inhibitor for the Coal Heap
- Experiment Study on Formula and Field of the Dust Suppressant for the Open Mine Road
- Freeze-Thaw Durability of Portland Cement Concrete Subjected to Aircraft Deicer
- Soy Protein Based Biodegradable Flexible Polyurethane Foam
- Effects of Ultrasonic on Properties of Modified Soybean Protein-Based Adhesives for Duplex Paper
- Research on the Calculation Method of Vertical Seismic Capacity of the Multi-Ribbed Composite Slab
- The Series K Criterion of Unstable Fracture of Concrete and its Application
- Study on Strength Distribution and Failure Probability Estimation of Structural Part of Foam Material
- Polyaniline/Epoxy Composite Emulsion Coatings for Anticorrosion to Mild Steel
- Preparation of Hyper-Branched Polymer and its Application in Synthetic Leather
- Effect of Sintering Technology on Ag/AgCl Electrode Potential Stability
- Effect of Load on Linear Reciprocating Sliding Friction and Wear Behavior in Zr-Based Bulk Metallic Glass
- Heat Transfer Characteristics in Exhaust Port for Hydrogen Fueled Port Injection Engine: A Transient Approach
Les mer
Produktdetaljer
ISBN
9780878492039
Publisert
2011-01-31
Utgiver
Trans Tech Publications Ltd; Trans Tech Publications Ltd
Vekt
3700 gr
Høyde
240 mm
Bredde
170 mm
Dybde
100 mm
Aldersnivå
P, 06
Språk
Product language
Engelsk
Format
Product format
Heftet
Antall sider
1994