Preface and Conference OrganizationChapter 1: Alloys and Non-Ferrous MaterialsInfluence of Overburning on Microstructure and Property of 2024 Aluminum AlloyEffects of Nb Element on Mircostructure, Thermal Conductivity and Melting Point of Cu-Ni-Nb Alloy Prepared by Vacuum Arc-MeltingDissolution of Alumina in Molten Aluminum Electrolyte Based on Perforated AnodeSurface Characterization and Machinability of Zirconium Alloys in View of Jewelry ApplicationHot Deformation Behavior and Microstructural Evolution of Al-Zn-Mg-Cu Alloy with Different Starting StructuresDiscussion on Technologies of Preparation of Foam Aluminum Metallic Material by Infiltration Casting MethodEffect of Indium on Precipitation Kinetics of an Al8Si0.4Mg Cast AlloyInfluence of MgO on Calcium Aluminate Slag System with Lower CalciumProcessing Map of Mg-13Al-3Ca-3Zn-1Nd-0.2Mn Magnesium AlloyStructure and Dynamical Relaxation in Undercooled Liquid of Cu50Co50 with Miscible GapThe Effect of Mixed RE Elements on Microstructure and Mechanical Properties of Die-Cast AZ91D AlloyUse of Strain Energy Density W and Qo as Quality Indices to Study the Effect of Hipping on Cast Aluminium Alloy 354 under Different Aging ConditionsStrain Rate Sensitivity and Adiabatic Shear Deformation of an Advanced Al-Mg AlloyComparison of Mechanical Properties of 357-T6 Aluminum Alloy Aast under Gravity Permanent Casting and Low Pressure Die CastingDiffusion Bonding of Commercially Pure Titanium to Q235B Using Copper as InterlayerMechanical Properties of A356 Aluminum Cast Alloy Shaped by Permanent Mold CastingSuperplasticity Mg Alloy Fabricated by Friction Stir ProcessingThe Technique Study on Silicon Brass Recrystallization Annealing Aided by Electric Pulse TreatmentWettability, Surface Tension and Work of Adhesion of Cu-Ti Alloys on Yttria Partially-Stabilized Zirconia at 1273KCombustion Synthesis Sintering of Ni-Al Powder AlloysInfluence of High Magnetic Field on β-a Phase Transformation in TC4 Titanium AlloyLow Temperature Superplasticity of 5083 Aluminum AlloyPrediction of TCP Phases in Nickel-Base SuperalloysChapter 2: Iron and SteelBake Hardening Properties of Ultra-Rapid Annealed Ultra-Low Carbon Bake Hardening SteelStudy on Internal Quality of Billets for 20CrMnTiH SteelStudy on Microstructure and Properties of X80 Pipeline SteelStudy on Microstructure and Property in Heat-Affected Zone of X80 Pipeline SteelThermal Simulation Study of CGHAZ Austenite Grain Growth Behavior of X80 Pipeline SteelResearch on Mechanics Performance of TP304H Austenitic Stainless Steel in the Process of Aging at High TemperatureExperimental Study on Hydrogen Selective-Reduction of Niobium Containing Iron Ore PowderResearch on the Corrosive Factors of Q235 Steel in Simulate Ammonium Sulfate Solution of Ammonia DesulphurizationMicrostructure and Mechanical Property Analyses of Brazing Titanium and Low Carbon Steel Using Silver-Based Brazing AlloyResearch and Application of Basic Tundish Covering FluxResearch of Producing Reduction Steel Powder from GCr15 Steel ScrapThe Research Status of Titanium Clad SteelOxidation Behavior of T91 Steel in Water Vapor Atmosphere at 750°CResearch on the Size Distribution of Intragranular and Boundary Carbides of T91 Steel after CreepAnalysis on Alloying Elements of Selective Oxidation of TRIP SteelHigh Temperature Oxidation Behavior of SUS310S Austenitic Stainless SteelPreparation and Characterization of Iron-Oxide-Coated-Zeolite AdsorbentExperimental Study on Refractory Weathering Steel Cold-Rolled Sheets Recrystallization AnnealingAnalysis of Boride Phase Composition in High Boron Alloyed Stainless Steel Containing TitaniumChapter 3: CompositesSynthesis of Sulfur-Doped Graphene from Sulfonated PolystyreneThe Properties of the Sodium Silicate Binder Composition Based on Quartzite DepositsStudy on Microstructure of Continuous Cf/Al Composite Material Prepared by Hot Pressing Diffusion MethodChange Regulation of Hardness of Target around Crater Penetrated by Wf/Zr-Based Amorphous Matrix Composite ProjectileAdsorption of Cu(II) from Aqueous Solution onto Na-Bentonite/Poly AMPS/AA/AM CompositeEffects of Fillers on the Dynamic Properties of a High Performance Elastomer at Varying Strain AmplitudeMorphology, Thermal, Dynamic Mechanical and Mechanical Properties of Long Glass Fiber Reinforced Thermoplastic Polyurethane Elastomers and Polyvinyl Chloride CompositesInvestigation of Surface Roughness after Turning of One Kind of the Bio-Material with Thermoplastic Matrix and Natural FibersMicrostructure and Tribological Properties of Cu-Fe Based Braking MaterialsPreparation and Wear Performance of Novel Graphite/Copper Alloy-Matrix Self-Lubricating Composite MaterialsThe Fabrication of High Silicon-Aluminum Composites and the Thermal ConductivityStudy on Properties of Modified Porous Starch/ Natural Rubber CompositeThe Influence of SiO2 on Properties of Cellulose AerogelDesign, Fabrication and Characterization of Fused Silica-Based Composites with an LTCC-Derived FSSEffect of Cycle Index on the Microstructural Evolution of Alumina Particles Reinforced Aluminum Composites Treated by Cryogenic TreatmentInfluence of Cooling Speed on the Microstructure of Particles Reinforced 7055Al Composites Subject to Regulatory Cryogenic TreatmentPreparation and Characterization of Resin-Derived Carbon Foams Containing Hollow MicrospheresA Study of Polyurethane Rubber Composite Modified Asphalt MixtureFluorescence Properties of Electrospun Bio-Based Polyamide/Eu(TTA)3phen Composite FibersPreparation of Poly(m-toluidine)/Montmorillonite Composites and its Thermal StabilityEffect of Diffusion Annealing on Defects Reduction of 6.5wt% High Silicon Steel Composite Plate after Hot DeformationInvestigation of Heat Treatment’s Influence on the Preparation of High Silicon Steel Composite SheetIron Loss Measurement on 6.5wt%Si Composite Plate Prepared by Clad Casting and Conventional Rolling ProcessesProduction of 6.5wt%Si Composite Thin Sheet by Cold Rolling ProcessStudy on Heating Treatment of 45steel/60Si2CrA Multi-Layer Composite Armor PlateStudy on Mechanical Property of 1Cr17/9Cr18MoV Multilayer Composite Armor PlateStudy on Superabsorbent Material in Thermal Infrared CamouflageChapter 4: Micro/Nano Materials and TechnologiesA Hydrogen Peroxide Electrochemical Sensor Based on Co-Doped Fe3O4 NanoparticlesEffect of Collect Distance on the Fabrication of Aligned Nanofiber by Parallel ElectrodeResearch Profiling of Carbon Nanotubes from 2000 to 2013The Raman Properties of Ag Doped ZnO Microrods Synthesized by Chemical Vapour DepositionLarge-Scale Synthesis of Water-Dissoluble NanorodsFabrication of PLA Nanoporous Fibers by DMF/CF Mixed Solvent via ElectrospinningFabrication of PEG Hydrogel and PDMS Microstructures by a Simple UV Curing Process for Nanobio-Chip ApplicationsPerformance of Electrospun Nanofibres on Adsorbing Gaseous Aromatic CompoundsProperties of Metallic Materials after Surface Self Nano-CrystallizationSimulation of Electric Field for Carbon Nanotube Assembly by DielectrophoresisThe Influence of Zn/Zr Ratios on CuO-ZnO-ZrO2 Catalysts for Methanol Synthesis from CO2 HydrogenationModification of the Fine - Aggregate Concrete by High Disperse Silica Fume and Carbon Nanoparticles Containing ModifiersPreparation and Mechanics Properties of the EP/TiO2 NanocompositesProgress of Studies on Fabrication of TiO2 Nanotube Arrays on Ti or Ti Alloys by AnodizationStudy on Preparation and Property of Regenerated Liquid Reactive Dyes Regenerated MagentaThe Effect of Different Ratio in Carbon Aerogel on Pore Structure in Ambient DryInfluence of Softener on Rheological Characteristics of the Nanostructured ModifierInsertion versus Growth of Magnetic Nanoparticles in MgB2 Superconducting CompositesHigh Density Dislocation and Magnetoplasticity in Nano-Sized Alumina Reinforced 7055Al Composites Subject to High Magnetic FieldEffect of Carbon Nanotubes on Microstructure of Multiphase Composite Al2O3 CeramicsQuasicontinuum Analysis of Dislocation Propagation during NanocontactPrepare and Formaldehyde Sensing Properties of Hollow Nanofibers In2O3Polarization Dependent Nonlinear Absorption in Au Nanowire ArrayResearch on Surface Modification of Nano-TiO2Enhanced Mechanical Performance of Electrospun Graphene/Polyacrylonitrile (PAN) Composite Microfibrous Yarns via Post-ProcessingInfluence of Complexing Agent on the Structure and Properties of Electrodeposited Fe–Co Alloy NanowiresChapter 5: CeramicsDispersion Stability of Hydroxyapatite-Calcium Phosphate Glass Ceramic-Tertiary Butyl Alcohol SystemMicrowave Dielectric Properties of Low-Fired Nd2Ti2SiO9 Ceramics with BaCu (B2O5) AdditionEffects of Cr2O3 Addition on Mechanical and Electrical Properties of Alumina CeramicEffect of Copper Micro-Scale Excess on the Dielectric Properties of CaCu3Ti4O12 Ceramics Prepared via Tape CastingEffect of H3BO3 Additive and Forming Pressure on Microwave Dielectric Properties of 0.95MgTiO3-0.05CaTiO3Sintering Behavior of Lead Oxide Ceramic Prepared by Microwave SinteringResearch and Transformation of Rotary Surface Discharge Machining Equipment of Engineering CeramicEffect of Tb4O7 Doping on Wear Resistance of High-Alumina CeramicLow-Temperature-Tunnel of High-Alumina Ceramics with Good Wear ResistancePreparation of the System of MgO-CaO-SiO2-Al2O3-Y2O3Wear-Resistant Alumina CeramicsStudy of Nonlinear Current-Voltage Characteristic of Semiconductor Ceramic by the Method of Tilted Energy BandThe Ways to the Main Problems in the Application of Low Temperature Co-Fired Ceramics Technology (LTCC)Study on the Crystal Bonding Mechanism of Al2O3–ZrO2 Ceramic CompositeEffect of Calcite Content on Firing Characteristics and its Sintering Properties of Nixing PotteryAnalysis of Pop-In Phenomenon in the Process of Ceramic Materials Instrumented IndentationChapter 6: Optical/Electronic/Magnetic Materials and TechnologiesA Life Prediction Model for LEDs Lamps Based on the Thermal Life TheoryCharacteristics Research of Gallium Arsenide Solar Cells under Femtosecond Laser IlluminationResearch on the Mechanism and Model of Contact ResistanceTest Systems for Life of LED Light Based on Junction TemperatureThe Modification of Anatase TiO2 (001) Surface by N or S Atom: A DFT InvestigationEffect of Temperature on LiMn2O4 Prepared by Molten-Salt Combustion SynthesisElectrochemical Title Performance of LiMn2O4 Synthesized by Flameless Solution Combustion with Acetate SystemCarrier Injection in High Gain GaAs Photoconductive Semiconductor SwitchesModeling of the Stress-Dependent Hysteretic Dynamics of Ferroelectric MaterialsSynthesis, Characterization and Photophysical Properties of a New CuI Complexe Contain Bis[2-(diphenylphosphino)phenyl] ether and 7,10-Dimethyl Pyrazino [2,3-f][1,10]phenanthrolineResearch on Bonded NdFeB Arc-MagnetsElectron Avalanche Domains in High Gain Semi-Insulating GaAs Photoconductive Semiconductor SwitchesManufacture Technology for Large Lightweight Optical MaterialsA PbS/ITO/Glass Based Photoelectrochemical Cell with a Sponge-Like Surface StructurePhotoionization in GaAs Photoconductive Semiconductor SwitchesResearch and Implementation on Methods of Evaluating Lifetime of LED Light Source for LED Lighting SystemSynthesis of a Novel Donor Unit for Organic Light-Emitting Materials: 10-octyl-3,7-Di(thiophen-2-yl)-10H-phenothiazineChapter 6: Optical/Electronic/Magnetic Materials and TechnologiesThe Luminescence Properties of Ca3(BO3)2 Doped with Ce3+, Tb3+Technological Development of 6.5wt%Si Electrical Steel ProductionInfluence of Nd-Doping on Electronic Structure and Optical Properties of ZnOOptical Properties of 5,5'-(9,9-dioctyl-9H-fluorene-2,7-diyl)Bis(thiophene-2-carbal dehyde): A Novel Organic Light Emitting MaterialFabrication and Lead Ion Removal Property of Magnetic Hydroxyapatite Composite with Hierarchically Urchin-like MicrostructureStudy on Microwave Absorbing of Tourmaline and Dravite/ZnO Complex PowdersModelisation of Permeability as a Function of Induction and Temperature by the Brillouin’s Function for the Formalization of the Magnetothermal ProblemChapter 7: Building and Construction ResearchComparison Study on Road Performance of Modified Asphalt Mixture for Intermediate CourseEstablishment and Research on the Rebound Curve to Detect Pump Concrete Compression Strength with ResiliometerFinite Element Analysis of Dynamic Splitting Tensile Mechanical Properties of Reinforced ConcreteFlush Rule and Initial Flush Analysis of Cement Concrete PavementMechanism Analysis on Concrete Column’s Recovery StrengtheningStudy of Bond Behavior between Concrete and Steel Bars Based on New Beam SpecimensStudy of Model Tests on Large-Span Tunnel’s Damage Caused by Overload with Arch Cover MethodStudy on Moment-Curvature Hysteretic Model of Steel-Concrete Composite Box BeamResistance of Polymer Dispersion Additive Modified Concrete to Light Liquids ActionAnalysis on Bearing Capacity of Retaining Wall with AnchorExperimental Study on the Mechanical Properties of the Crumb Rubber Concrete Modified by LatexThe Introduction of Micro-Pile in Building Heightening and TransformationA Study on the Snowdrift Patterns of Gable and Flat Roofs Using a Wind TunnelEffect of Co-Doped Steelmaking Slag and Fly Ash on Performance of Permeable ConcreteExperimental Research on Shear of Interface between New and Old Concrete with Bond-In Reinforcement and Practical CalculationExperimental Study on Ratio of Bending-Compressive Strength of the Crumb Rubber Concrete Modified by LatexNonlinear Analysis of Concrete-Filled Steel Tubular Columns under Blast LoadingStudy on the Ultimate Bearing Capacity of Concrete Filled Steel Square Tubular Short Column with PBLA Study on Influence of Shape of Aggregate on Strength and Quality of Concrete for Buildings and PavementsInfluence of Superplasticizer S-3 on the Technological Properties of Concrete MixturesTests Results Strength and Thermophysical Properties of Aerated Concrete Block Wall Samples with the Use of Polyurethane AdhesiveApplicability Study of Peck Formula Applied to Shield Tunneling in the Loess AreaBearing Performance Test Research of Shallow Arch Circular Concrete Filled Steel Tube SupportCurrent Status and Development Trend of Assembled Structure in Cold RegionsThe Energy Efficiency of Residential Buildings with Light WallingHighly Filled Building Materials Reduced FlammabilityModern Building Materials and the Concept of "Sustainability Project"Research on the Influence of Fiber Web to the Axial Compression Performance of EPS Composite Insulation WallboardRestrained Shrinkage Behavior of Concrete under Different Environmental ConditionsRisk Evaluation of the Subway Foundation Pit Based on Variable-Weight and Matter-Element TheoryThe Implementation of Waste Sawdust in ConcreteElectrochemical Behaviors of Q420 Hot Galvanized Plate in Simulated Concrete Pore SolutionModernization of Residential Buildings of the 1960sShear Strengthening Effects of RC Beams Using Aramid Plate StripThe Quickly Erected Buildings in Modern ConstructionCompound and Engineering Application of Fiber Reinforced Concrete with Low ShrinkageThe Research of Concrete Short Columns Strengthed with Angle SteelMicrostructure and Mechanical Properties of Laminated Mg-Based CompositesThe Engineering Application of Carbon Fiber Reinforced Concrete BeamModeling of Reliability for Anti-Condensation Wall System in Underground Engineering Based on Markov ProcessThe "Comfort in all Respects" Principle Implementation by the Example of an Elementary SchoolCharacter and Development Analysis of Foam Concrete Cooperating Rice Husk AshThe Energy-Efficient Heat Insulation Thickness for Systems of Hinged Ventilated FacadesShield Tunneling Parameters Optimization Based on Dynamic Bayesian NetworksThe Historical Characteristics and New Developments of Settling Spaces on BridgesChapter 8: Environment-Friendly MaterialsEffect of Formamide on the Mechanical Properties of Thermoplastic Protein FilmsMechanistic Study on Adsorption and Oxidation of NO over Activated CarbonStudy on Metal Chelation Adsorption of NO Using Fe(II)EDTA Solution in Power PlantImpact of Biochar on Water Holding Capacity of Two Chinese Agricultural SoilApplication Research of Slow-Release Fertilizer in Plant CamouflageStudy on CO2 Adsorption of Sepiolite Modified by Silane CouplingThe Full Immersion Test Research of Refractory Weathering SteelHydraulic Performance of Olive Stone Filtration SystemsOrganobentonites for Controlled Release of DiazinonStudy on the Storage Stability of High Neutralization Degree Phosphate-Bonded No-Bake SandChapter 9: Biomaterials and BioresearchA Comparison Study of the Effects of Ultrasonication on the Gelation Behavior between the Silk Fibroin of Domestic and Wild SilkwormsDetermination of Luteolin by Fluorescence SpectrometryDynamic Models of Cell Growth and its β-Carotene Synthesis from the Red Yeast MutantExtraction Technology and Determination of Total Flavonoid in Magnolia Liliiflora PetalsFractal Modeling Research in Permeability of Camellia and Bancoul Nut Cakes under Cold-PressImproving the Yields of Carotene from Red Yeast by Using Ultra High Pressure and its Mutagenic MechanismSynthesis of Tung Oil MonoglycerideAnalysis of Key Odor Compounds in Steamed Chinese Mitten Crab (Eriocheir sinensis)Chemical Constituents Study of Weixian Turnip (Raphanus sativus L.)Comparison of Volatile Compounds in Raw and Cooked Chinese Mitten Crab Hepatopancreas and GonadsEffect of Cold-Induced on Quality of Black Carp Fillet Stored at Controlled Freezing-PointMicrostructure Analysis of Xanthoceras Sorbifolia Shell Activated CarbonOptimization of Microwave Pretreatment without a Reagent of Pineapple PeelOptimizing Clarification of Pineapple PeelPreparation and Evaluation of Calcium Alginate/Glycyrrhizic Acid HydrogelPreparation of Antioxidant Hydrolysates from Round Scad (Decapterus maruadsi) Protein by Composite Enzymatic HydrolysisPurification of Enzymatically Produced Trehalose by Saccharomyces cerevisiae Strains Carrying Compound UV- and NTG-Induced MutationsThe Establish of Four Kinds of Chinese Primary Economic Crab Species Fatty Acid FingerprintsEffects of Water Temperature on Biochemical Characteristics of Mandarin Fish during Live TransportationThe Effect of Modified Atmosphere Packaging on the Quality of Sturgeon Caviar at 0°CCharacteristic Changes of Protein Occurring in Brine Salting Sturgeon at Different Levels of NaClComparative Analysis of Amino Acid Composition in Antarctic Krill and White ShrimpComponent Analysis, Quality Measurement and Antioxidant Activity of Sambucus williamsii Seed OilDicamba Degradation Using O3/UV Process in Aqueous SolutionPhysicochemical and Rheological Properties of Gelatin Extracted from Tilapia (Oreochromis niloticus) Skin and Concentration EffectPhysicochemical Properties of Biodegradable Tilapia Skin Gelatin Film and Gelatin-Polysaccharide Based Composite FilmsPlant MicroRNAs Responsive to Fungal InfectionShortening Fermentation Period of Fermented Sausage by Adding Exogenous EnzymesStudy on Defluorination Effect of Antarctic Krill by Chemical TreatmentsThe Expression Analysis of WUSCHEL Gene under High and Low Temperature in Tomato SeedlingThe Expression Analysis of the YABBY Transcript Factor-SlYABBY2a in the Tomato Seedling under Low LightTowards Enhanced Bioactivity: Calcium Ion-Doped PolypyrroleVacuum Assisted Extraction of Indirubin from Radix isatidis through Orthogonal Test MethodA Bioaerosol Detection IRLidarEffects of Different Purification Methods on Chicken Feather KeratinEffect of Different Temperatures on Storage Quality of Fresh-Cut ApplesFinite Element Analysis of Femoral Fracture SystemInfluence of Operating Parameters on Physicochemical Properties of Fruit Juice Powders Produced by Spray DryingChapter 10: Polymer MaterialsA Novel Cement Fluid Loss Additive P1402A Self-Oscillating Polymer Chain with High LCSTActivation Energy of Autonomous Polymer Chains with High LCSTPreparation and Drug Release Behavior of IPN Hydrogel of Polyethylene Glycol and Octane Succinyl ChitosanThe Optimization Plastic Coefficient in AWC Research and ApplicationEffect of Relative Humidity on the Morphology of Electrospun Gelatin Aqueous SolutionsMelting, Crystallization Behaviors and Mechanical Properties of iPP Nucleated by β Nucleation MasterbatchesRheological Properties of all Para-Position Polysulfonamide Spinning SolutionsSimulation of the Flow-Induced Crystallization of Polypropylene Based on Molecular Kinetic ModelStudy on Resin Infusion Behavior of the CFRP Integrated Manufacturing Process Based on RFI ProcessA Novel Synthesis Process of PPTA by Nitrogen Cooling for Reaction Heat RemovalCrystallization Behavior and Crystal Morphology of PP/POEg BlendsThe Kinematic Research in the Manufacture of Rigid Polyurethane Rubber Micro-V GroovesInfluence of Solvent Content on Properties of UHMWPA6 Fibers Prepared by Gel-Spinning MethodChapter 11: Film MaterialsFabrication of Self-Organized Porous Anodic Alumina Film in Malonic AcidEffects of Thickness on Resistance Switching Properties of ZnMn2O4 Films Deposited by Magnetron SputteringInvestigation of Phase Transformation and Optical Properties of TiO2 Thin Films Deposited by Electron Beam EvaporationReaction Mechanism of Atomic Layer Deposition of Al on the Si (100) Surface: A Density Functional Theory StudyEffect of Al-Induced Crystallization on Structure of CdZnTe Thin Films Deposited by Radio Frequency Magnetron SputteringInfluence of Sputtering Power on the Properties of CdS Thin Films Deposited by Magnetron SputteringRecent Progress in Gasochromics of Nano-Structured WO3 Film and its ApplicationsStructural and Optical Properties of (Al, Co) Codoped-ZnO Thin FilmStudy of the Capacitive Properties of Strontium Barium Niobate Deposited by Radio Frequency Magnetron SputteringChapter 12: Textile Materials and TechnologiesEco-Friendly Dyeing of Silk Fabric with Sodium Copper ChlorophyllFabrication of Twisted Continuous Nanofiber/Cotton Hybrid YarnsThe Exploration of Nickel Iron Fiber Absorbing FabricChapter 12: Textile Materials and TechnologiesAnalysis on down Coat FabricDesign Principle and Method of Digital Multicolored Warp Jacquard FabricParameters of High-Density Soft Breathable and Anti-Velvet Fabric TechnologyResearch on the Ballistic Performance of UD Cloth/3D Fabric Composite TargetTesting of the Dynamic Permeability and Deformation of Airbag FabricsComparative Study between DSC and Two Complementary Performance Evaluation Methods for PCM-Treated TextilesChapter 13: Corrosion and Surface Treatment TechnologyThe Effect of Wear and Corrosion Resistance of Austenitic Stainless Steel on Plasma CarburizingStudy of EMISE Ionic Liquids Inhibitor on the Corrosion Behavior of Steel Rebar by Statistical Methods in Alkaline Chloride SolutionMultiple Regression Corrosion Models and Corrosion Mechanism of High Chromium Cast Iron under Phosphoric Acid Medium ConditionApplication of Visual Basic (VB) Language on Stress Corrosion Cracking Test of MaterialsOxidation-Resistance of (Ti,Al,Nb)N Coatings Prepared by Arc Ion PlatingInteraction Concrete with Acidic FluidsApplication of Origin in Material Corrosion ExperimentEffect of New Corrosion Inhibitor on Electrochemical Behavior of Prestressed Steel Wire in Simulated Concrete Pore SolutionImpact of Local Concrete Crack on the Prestressed Steel Stress Corrosion CrackingIndustrial Application of Pb–Ag–Ca Anode with Surface Passivation for Zinc ElectrowinningInvestigation on Electrochemistry Behavior of Fe-Cr-Ni Alloy in Caustic SolutionResearch on the Nitriding Effect of Ta-10W with Change of Process ParametersThe Micro-Fabrication of Multidimensional Structure of Silicon by Selection CorrosionProcess Design of Strengthening and Toughening Treatment for 65Mn Steel by Powder RE-Boronizing Method under Low TemperatureChapter 14: Materials Mechanical Behavior and FractureAnalysis on Fracture Mechanism of T92 Steel under High Temperature Multiaxial CreepBallistic Resistance of AA5083-H116 Aluminum Plates against Conical-Nose Steel Projectiles ImpactPiston Contact Stress Analysis and SimulationThe Damage Analysis of Composite Laminate under the Action of Low Speed Impact and Static Pressure MarkDevelopment and Change of Compressive Strength for Class G Oil Well Cement under High TemperatureMethod for Determining the Plastic Properties of Metallic Materials by Instrumented Indentation with Dual Pyramidal IndentersStudy on Flow Mechanism of Gas Injection in Porous Carbonate CoreEffect of True Strain on Processing Maps for Processed Ni-Based Superalloy below γ΄-Transus TemperatureEffect of Strain on Microstructures and Mechanical Properties of Warmly Deformed SCRAM Steel for Fusion ApplicationInfluence of Carbon on Mechanical Behavior of Fe-Mn-C System AlloysMultiscale Simulation of Crack Propagation Based on Molecular DynamicsNumerical Simulation Study on High-Cycle Fatigue Damage for MetalsEvaluation of Mechanical Properties of Hastelloy C-276 Weld by Small Punch TestConstitutive Modeling for Superplastic Flow Behavior of H62 AlloyCorrelation Degree Analysis on Temperature and Operating Pressure to Stress Corrosion Cracking SusceptibilityExperimental Study on Shot Peening to Improve Diaphragm Spring Fatigue Life of Automobile ClutchPrediction of Flow Stress for Superplastic Tension DeformationQuantitative Analysis of Instability for Superplastic TensionTheoretical Deduction of Constitutive Equations with Variational Parameters during Superplastic TensionInfluence of Grain Size and Lamellar Spacing on the Fatigue Crack Propagation in γ-TiAl AlloyStudy on the Microstructure and Fracture Mechanism of Stable β Phase Containing Tial AlloyThe Fatigue Behavior of Carbon Fiber-Reinforced Composite T300/Epoxy under Tension-Tension and Bending Fatigue LoadingResearch on the Relationships between Plastic Viscosity of Picking Liquids and its Tack ValueTexture Evolution of Commercially Pure Copper during Ultra-Thin Strip RollingRegularity of Decreasing Strength Limit at the Time of Concrete's Freeze-Thaw CyclingThe Preparation and Tribological Properties of Graphite FluorideNonlinear Model and Numerical Solutions of Large Deformation of Functionally Graded Conical ShellCalculating Fatigue Life of Helicopter Composite Blades Based on the Residual Strength TheoryAircraft Composite Structures Fatigue Durability Test MethodThe Preparation and Performance Study of Thermal Insulating Materials with DiatomiteMechanical Response of Ping-Pong Racket to Different Hyperelastic Surface MaterialsResearch on Grind-Hardening Process through Integration of Physical Experiments and Dynamic SimulationChapter 15: Surface Engineering / Coatings TechnologyHydrophobic Coating on Silicon Wafer by Use of Industrial Coating-Bar Process in Atmosphere ParameterSlip Length Measurement of Water Flow on Graphite Surface Using Atomic Force MicroscopeThe Influences of Additives and Heat Treatment on the Properties of Electroless Plating Ni-W-Mo-P Alloy on the AluminumResearch and Development on the Antiaging Polymer CoatingsPreparation and Characterization Composite Ceramic Coating Doped with ZrO2 Particles on TC4 by MAOPreparation and Characterization of Al(OH)3 Coated CaF2 Composite PowderPreparation of Pd Composite Membrane and its Surface Morphological Changes after Elevating Temperature in Different AtmoshphereResearch on the Microstructure and Properties of Coating on Galvannealed High Strength IF SteelPreparation of PAI Composite Coatings and its Tribological BehaviorsNew Technology of Electroless Silver Plating on Fly Ash Cenospheres with Thermo-Alkaline ActivationPreparation of Superhydrophobic Surfaces with Different Degrees of OleophobicityProgress in Thermal Barrier Coatings for Gas Turbine EnginesFE Modeling of Stress Distribution in MAO Coating on TC4 Substrate under Thermal Shock Cyclic LoadingInvestigation of Durability T = f (vc) in Turning of the AISI 304 Austenitic Stainless Steel Using the CNMG 120408 Coated Carbide InsertResearch on Wear Characteristics of CVD Composite Coated Tool in Natural Marble CuttingDensification Behavior and Microstructure Evolution of Laser Surface Melting Processed Silicon-Containing Micro Arc Oxidation CoatingInfluence of Additive on Morphology and Nucleation Mechanism for Zn-ElectrodepositionPreparation and Antimicrobial Properties of Surface Antibacterial Layer of AluminumChapter 16: Forming TechnologiesEffect of Drawing Processes on Wire Breaking in Steel Wire ProductionEffects of Parameters on Fine Blanking of Steel Synchronizer Ring TeethRunner Balance Design of Soap Box Compounding Cavity Based on MoldflowStudy on Deformation Law of Drum-Shaped Blank and Collapse Defect in Rolling ProcessStudy on Spring-Back of CU11000 Clad AL1050 SheetsThe Application and Research on Manufacturing Technology of the Heavy ForgingThe Application of Steady-State Thermal Expansion of the Rolls in Thickness Setup Model for HSMThe Optimization of Thickness Model Adaption in Hot Strip MillResearch on Tension and Correction of Filming Steel Strip on Hydrosol Salivation MachineExperimental Study on Three-Dimensional Flexible Stretch Bending Formability for Complex Cross-Sectional Profiles of TWBThe Effect of Screw Speed on Extrusion Quality of the Single-Screw ExtruderNumerical and Experimental Investigation on Hot Stamping of Ultra-High Strength SteelCoupled Thermo-Mechanical FEM Simulation of Multi-Pass Vertical-Horizontal Rolling ProcessDevelopment of Environmentally Friendly Binder in Extrusion MoldingEffect of Mid-Roll Shift on the Strip Flatness for CVC 6-H MillEffect of Steel Strip-Feeding Process on Solidification StructureMetal Average Deformation Velocity and Forward Slip Model for Longitudinal Profiled Plate Rolling ProcessOptimization Design of Evaporator Tube Plate Mold Based on PDXStress-Strain Analysis of the Sun Shaft in Cross-Wedge-RollingStudy of Isothermal Split-Die Precision Forging Process of High-Strength Aluminum Alloy Complex-Shape ForgingsStudy of Submacroscopic Melting of Polymer in Single Screw Extrusion - Physical Model of Polymer Granule MeltingStudy on the Influence of Thickness and Width on the Post-Buckling Deformation of Cold-Rolled StripTechnique of Extrusion Die Tolerance Analysis Based on CATThe Influences on Microstructure and Segregation of the Jumbo Slab Ingot by Different Cooling SpeedOn-Line Measurement of Rheological Properties of LDPE, HDPE and LDPE/MICA Systems in Single-Screw ExtrusionStudy on Convergence, Calculation Speed and Precision of Flatness Analysis Method for Cold Rolling StripCauses and Remedies for some Physical Defects in Rotary Swaged ProductsExperimental Investigation on Rotary Punching by the Compression of Polyurethane PadInfluence of Rotary Forging Process on Microstructure and Properties of Niobium-Titanium AlloyKey Technical Analysis of Roll Forming for High Strength Rectangular TubeNumerical Simulation of Polyurethane Pad Punching ProcessPreliminary Investigations on Preparation of Cu-Al Bi-Metallic Tubes Using Swaging-Diffusion MethodResearch Status of Sheet Metal Blanking ProcessesTechnology of Finite Element Analysis for Roll Forming ProcessAnalysis of Metal Deformed Flow under Adhesive Friction by Ring UpsettingInvestigation on the Effect of Liquid Hammer Geometry to the Pressure Distribution of Innovative Hybrid Impact HydroformingLarge Container End Plate Stretch Forming TechnologyOval Aluminum Tube Extrusion Process Simulation with Two-Hole DiesResearch on Finite Element Simulation of the Big Size Spring Steel in Continuous Grooveless RollingThe Ring’s Axial Deformation Control Method of Vertical Hot Ring Rolling ProcessProblems of Cold-Bent Notched C-Shaped Profile MembersStudy on Simulation and Experiment of Micro Sheet Metal FormingThe Pressed Products on the Basis of GypsumEffect of DROF Process on the Temperature Field and Roll ForceSimulation to the Temperature Field for Continuous Casting Billet during Direct Rolling of Free-HeatingThe Strain Analysis of Plate Cross Wedge Rolling of Spiral Shaft PartsResearch on a Kind of no Punch Hollow Part Hydraulic Pressure Expand MouldManufacturing Process for Bush Type Bearing Metal Using Centrifugal CastingChapter 17: Material MachiningEfficiency Analysis on the Synthetically De-Icing Technology Combining Thermal Water-Jet Cutting with Mechanical MillingStudy on Cutting Performance of the Alumina Based Nanocomposite Ceramic ToolTC4 Titanium Alloy Surface Crack Detection and AnalysisA Processing Predictive Model of Ultrasonic Vibration Grinding Assisted Electric Discharge Machining Based on Support Vector MachinesDesign and Tuning of the Ultrasonic Wide-Blade Horn for Joining and Cutting Non-Woven FabricsStudy on Virtual Machining Process of Peripheral Milling of Thin-Walled WorkpieceThe Evaluation of the up and down Milling Based on its ChipExperimental Study on Effects of Feed per Tooth on Shear Angle and Friction Angle in Orthogonal Milling of Titanium AlloyExperimental Study on Electrochemical Drilling of Micro Holes with High Aspect RatioChapter 17: Material MachiningStudy on Material Removal Mechanisms of Surface Fatigue Layer Based on Handheld High Velocity Arc MachiningExperimental Study on the Optimization of Ti1023 Milling ParametersResearch and Development of Ultrasonic CNC Cutting Path Generation System for Nomex Composite MaterialsOptimization of Electric Discharge Machining Parameters of Al-7%Si-4%Mg with 20% of Red Mud Metal Matrix CompositesSimulation of Residual Stress in Cold Working of Flat Spiral SpringsPolishing Experiment Study of the Elastic Coated AbrasivesMachinability Assessment of Titanium Alloy Ti-6Al-4V for Biomedical ApplicationsStudy on Key Technologies of Handheld High Velocity Arc Machining EquipmentThe Cooling Characteristics of Quenching Mist under Different ConditionsChapter 18: Welding and JoiningMicrostructure and Bending Property of Welding Joint Prepared by 5356 Welding Wire Added Sc, Zr and ErStudy on the Thermal Expansion Displacement during Spot Welding Depending on the Multi-Physical Coupling Finite Element ModelResearch on the Laser Welding Technology of LF21Study of End Cracking during One-Sided Submerged Arc Welding with Flux-Copper BackingArc Characteristics and Droplet Transfer Analysis of Disconnect Impulse Arc Welding for Repairing Surface Default of Metal PartsInfluence of Heat Treatment on Microhardness and Microstructure of the Joining Interface for Ti-24Al-15Nb-1.5Mo/TC11Microstructure and Properties of Mg/Al Dissimilar Joints by GTAW with Al-Si Filler WireResearch on Surfacing Welding and Machining Process of Large Valve Corrosion Resistant LayerThe Effect of Joule Heat on Coupling Temperature Field of Friction Stir WeldingThe Microstructure and Properties of TIG Welded Joint of AZ31B/Cu Dissimilar MetalUltrasonic Horn Design and Weldability in Thin Ni Plates WeldingExperimental Research of Activating Fluxes in A-TIG Welding of 5052 Aluminum AlloyRelationship between the Microstructure of the Welded Steel Plates and the Efficiency of Vibration Stress ReliefWeld-Bonded Joints Properties with Advanced High Strength Steel DP600Sealing of Sapphire Infrared Windows by Ultrasonic Interfacial Deposition SolderingThe Implementation of Martensitic Heat-Resistant Steel Welding Performance Analysis and ProcessCharacteristics Evaluation of Weld and Deposited Metal Zones in the Case of Welded with Inconel 718 Filler Metal to Cast Steel for Piston Crown MaterialPerformance of Cohesive Zone Models for Brittle and Ductile AdhesivesImprovement of the Wear Resistance of A6061 Plate by Resistance Seam Welding with High Carbon Iron Alloy PowdersWelding Spark Parameters Determination for Cyclone Removal CalculationChapter 19: Micro-Fabrication TechniquesExperimental Research of Hydrogenous Fuel Production from Biogas for Usage in Fuel Cells of Autonomous Power Supply SystemsHigh-Speed, High-Precision Magnetic/Piezoelectric Hybrid Drive Actuator for Micro Electrical Discharge MachiningInfluence of Grain Size and Grain Boundary of Workpiece on Micro EDMModel Structure and Simulation Analysis of a Novel Magetic Suspension Spindle Apparatus for Micro EDMStudy on the Effect of Tool Polarity and Tool Rotation during EDM of Non-Conductive CeramicsThe Periodical Translocation Gear-Grinding Technique to Improve the Indexing Accuracy of Ultra-Precision GearsExperimental Investigation of Fabrication of Double Tapered Hole Array by Using Electroforming and Mask Electrochemical MachiningExploration of Hyperfine Micro-Machining LimitMicrofluidic Chips with Micro-Pillar Array for Cell CaptureThermal Accumulation in Metal Micro-Parts Fabricated by Micro Droplet Deposition Manufacturing TechniqueChapter 20: Laser Processing TechnologyContrast Prediction for Laser Direct Part Marked Data Matrix Symbols on Titanium Alloy SubstratesStudy of Effect of Laser Marking Data Matrix Symbols on Titanium Alloy Sheets Using Nd:YAG LaserExperimental Research on Affect of Water Jet to Laser Compound Processing of Crystalline SiliconInfluence of Laser Input Current and Water Jet to Etching Amount of Polycrystalline Si WaferThin Wall Formed by Multi-Layer Overlapping Laser Cladding FormingLaser-Energy-Density Dependent Formation of Al2O3-TiC Coating by Laser-Assisted CombustionDirectly Manufacturing Mouse Mold by Plasma Deposition ManufacturingSLC Technologies for Ferroalloy Part Surface ModificationLaser Cladding of Co-Based Alloy on 316 Stainless SteelFormation of TiC0.3N0.7/TiN Composite Film on Ti-6Al-4V Alloy by YAG Laser IrradiationChapter 21: Machining Tools, Testing Technologies and Error MeasurementNew Method of Plane to Plane Parallelism Error Measurement Based on Flatness PlaneModeling and Identification of Geometric Error Based on Screw TheoryMeasurement Uncertainty Evaluation of a Virtual Instrument for Thickness Monitoring of Brush-Plated CoatingEfficient Genetic Algorithms for Measurement of Flatness Error and Development of Flatness Plane Based on Minimum Zone MethodSimulation Analysis and Experimental Study of Initial Permeability Testing TechnologyThe Study of Closed-Loop Position Control System Based on CNC ProcessingChapter 22: Modeling, Analysis and Simulation of ProcessesInfluences of Edge Rolling on Unsteady Deformation of Metal in Roughing Stage of Continuous Hot Strip RollingMathematical Model of Topology Modification of Tooth Surface and Error CharacteristicsModeling for HAGC Press System of Rolling MillComputational Solution of Contact Problems with Unilateral Constraints and Friction by Step-by-Step AnalysisSimulation and Analysis of Material Horizontal Vibration Conveying Based on DEMThe Fiber Orientation Angle Determination for a Composite Anisotropic Solid Rod in PultrusionApplication of Two Damage Identification Methods Based on Sensitivity Analysis in Steel StructurePrediction and Control of Hot Pressing Rebound of Fan Blade Based on Thermal Mechanical Coupling SimulationAnalysis of an Orbital Grinding System for Grinding Crankshafts for Large Ship EnginesInfluence of Cold-Rolled Strip Temperature on the Interference Fit of Entire Roller Embedded Shapemeter RollNumerical Simulation and Process Analysis for Injection Forming about the Thin-Wall Conical Centrifugal DiscNumerical Simulation of Liner Curvature Radius on Formation of LEFPStudy on Transverse Uniformity of Phase Transformation for Hot-Rolled Strip on Run-out-TableFinite Element Modelling of Copper by Equal Channel Angular ExtrusionHot-Rolling Batch Planning Problem of Round Bar with Roller CapacityModeling and Virtual Simulation of Hard Surface Milling and Forming Process Using Advanced CAE SystemsThe Inverse Prediction for Profile Extrusion Die Based on the Finite Element MethodA Numerical Approach for Simulating a Self-Contacted Elastic RodA Schwarz Alternating Algorithm Using Elliptical Arc Artificial Boundary for Exterior Problems with a Concave AngleMaterial Removal Model and Experimental Analysis in the CMP of Si-Based Fiber ArrayResearch on FEM Simulation of Splitting Spinning Progress about 2024 Aluminum AlloyFinite Element Simulation of Seven-Hole Propellant Extrusion and the Optimization of Die Compression RatioModeling of Multilayered Sheets for Thermoforming ApplicationsNumerical Investigation on Angle of Repose of Cylindrical ParticlesChapter 23: Thermal Engineering Theory and ApplicationsDiffusion and Oxidation Wear of Superhard Cutting Tool Based on Thermodynamics EnthalpyStress Modeling of Large Cylindrical Ingot Heating ProcessStudy of Crack Length Measurement and Crack Tip Plastic Zone Determination by Infrared ThermographyThe New Model of Laminar Cooling System and its Fieldbus SystemExperimental Research on Crock-Type Metal Fibre Burner of Chinese Cooking ApplianceCooling Rate, Microstructure and Property Studied of Spray Cooling of Heavy Shell Ring RollingThe Transient Temperature Field Simulation and Analysis of Machinery’s Components by ABAQUSNumerical Simulation Analysis of Rail Head for U75V in the Process of Spray Cooling Temperature FieldStudy on Energy Saving Model of Air Condition for Subway StationEffect of Normal Pressure on the Coupled Temperature Field of Pin-Disc in Electromagnetic EnvironmentExperimental Study on Film Cooling Efficiency of Flat Plate through Infrared Thermography TechniqueISO 11439 I-Cylinder Bonfire Test and Safety EvaluationModelisation of Calorific Capacity by the Debye and Brillouin Functions for the Formalization of the Magnetothermal ProblemEnergy Consumption Analysis of Thermal Regeneration of Activated Cokes Loaded with SO2The Influence from the Return Water Temperature of Condenser on the Cooling Capacity and Power Consumption of the Cold-Water Screw Unit Used on Cold StorageApplication of Thermal Contact Resistance in Simulation of Heat Dissipation by CPU Heat Sinks Based on ANSYSHeat Transfer Capacity of Composite Cooling System for Automobile Lithium-Ion Battery with Heat Pipe and Phase Change MaterialsThe Influence of the Position of the Steel Element to Heat Flow in the Wall of the Industrial FreezerEffect of Model Structure on Thermal Conductivity of Sandwich CompositesThermal Insulative Performance of Bamboo Leaf Aerogel Opacified Using Activated Carbon Compared with Carbon BlackThe Influence of Induction Heating to Remelting Temperature Radial DistributionTheoretical Analysis and Experimental Study on Heat-Transfer in Cryogenic Gas Atomization Jet Cooling Nickel-Base AlloyThermal Stress Distribution Simulation Analysis for Disc Brake of Heavy VehiclesThermomechanical Coupled Analysis of Multidisc Friction Pairs in Hydro-Viscous DriveThermal Structure Coupling Analysis of Universal Mill’s Horizontal Roller Ring Based on ANSYSThe Research of the Effect of Velocity on Coupled Temperature Filed in Pin-on-Ring Friction Pair under Electromagnetic FieldResearch on Design and Principles of New Regenerant for Restoring Performance of Aged PitchChapter 24: Mineral and Soil Mining and ProcessingHydraulic Fracturing Technology Design in Natural Fracture ReservoirsStudy on Floor Pressure Relief Law of Simultaneous Mining Working Faces in close Distance Seam Group of Dongsheng CoalfieldStudy on the Abutment Pressure and Advanced Support of Driving Roadway along Goaf of Isolated Mining FaceExperimental Study of Fill Body Non-Uniformity for Cut-and-Fill MiningSimulation and Analysis of Anti-Explosion Capability for Coal Mine Refuge ChamberThe Study of Remaining Oil Distribution in Tazhong 4 Oilfield’s TZ402CIII Oil GroupStudy of the Trellis Support of Working Face Roadway in Impact Coal SeamStudy on the Mining Induced Stress of Hard Surrounding Rock under Dynamic PressurePlugging Agent Type Selecting Methods for Channeling ReservoirStudy on Deep Reduction of Oolitic Hematite Assisted with Microwave RadiationStudy on Variation Regular Pattern of Development Indexes in Beierdong Block after Layer RecombinationEvaluation on Shale Gas Potential in the Sheling Group Yitong BasinFinite Element Analysis and Optimization Design on Single Screw Pump of Offshore Petroleum Well Cementing LADS DeviceThe Characterization of the Rock Microscopic Pore Structure before and after Strong Base ASP FloodingDiscussion on Support Problems on Soft Rock RoadwayResearch on Rock Mechanics Characteristics of Mud Sandstone NanTun Formation of HaiLaEr OilfieldAn Experimental Study on the Mechanical Properties of Cemented Rock-Tailings FillInvestigation on the Sintering Properties of Mullite Al2O3-70%Status Analysis of the Frozen Soil’s Dynamics Parameter StudyStudies about the Drained Creep Characteristic of Silt Soil on k0 ConsolidationCharacterization and Application of Super Clean CoalStudy on Extractiing of Heme from Tilapias Blood by Enzymatic Method