Frontiers of Manufacturing Science and Measuring Technology IV
Heftet /
2014
/ Engelsk
Produktdetaljer
ISBN
9783038351924
Publisert
2014-10-01
Utgiver
Trans Tech Publications Ltd; Trans Tech Publications Ltd
Vekt
4430 gr
Høyde
240 mm
Bredde
170 mm
Dybde
119 mm
Aldersnivå
P, 06
Språk
Product language
Engelsk
Format
Product format
Heftet
Antall sider
2376
Collection of selected, peer reviewed papers from the 2014 4th International Conference on Frontiers of Manufacturing Science and Measuring Technology (ICFMM 2014), June 19-20, 2014, Guilin, China.
The 487 papers are grouped as follows:
Chapter 1: Materials Engineering, Technology and Application,
Chapter 2: Applied Mechanics, Design, Simulation and Manufacturing,
Chapter 3: Measurement, Monitoring, Control and Testing Technologies,
Chapter 4: Communication and Navigation, Information Technologies, Algorithms and Numerical Methods, Image, Video, Signal and Data Processing,
Chapter 5: New Technologies in Education and Sports,
Chapter 6: Management Engineering, Business and Economics Engineering
Les mer
Selected, peer reviewed papers from the 2014 4th International Conference on Frontiers of Manufacturing Science and Measuring Technology (ICFMM 2014), June 19-20, 2014, Guilin, China
- Preface and Committee
- Chapter 1: Materials Engineering, Technology and Application
- A Comparative Study of Neat Epoxy Coating and NanoZrO2/Epoxy Coating for Corrosion Protection on Carbon Steel
- Analysis of Factors Influencing the Performance of Q460 Steel
- Development and Application of Aluminium-Lithium Alloy
- Friction and Rheological Properties of Meso-Porous MCM-41/Unsaturated Polyester In Situ Composites
- Experimental Study of Low-Pressure Water Jet Assisted Laser Drilling on Al2O3 Ceramic
- A New Method for Testing the Asphere Surface with a Liquid Crystal Spatial Light Modulator
- Analysis the Tool Wear of Screw Drill during the Drilling of Steel X04Cr16Ni12MnTiN
- Comparative Study of Different Cadmium Salts on Nano-Structured CdS Thin Films Prepared by CBD
- Corrosion Resistance of X52 Pipeline Steel at Sea Mud Zone
- Effect of Mn (II) Ion on Abrasive-Free Polishing of Hard Disk Substrate
- Experimental Study on Process Parameters of High-Speed Micro-Milling Al2O3 Ceramics
- Experimental Study on the Burning Behavior of Automotive Internal Decorating Materials
- Influence of pH Values on the Morphology and Down-Conversion Luminescence Properties of Zinc Tungstate Micro Nano Crystal Synthesized by a Hydrothermal Method
- Mechanical Properties Analysis and Application of Metal Matrix Composites
- Medical Building Materials of Structural Properties and Electromagnetic Interference Shielding in the Quartz Crystal Plane Coated Ni Based Thin Film
- Morphology-Controlled Synthesis of ZSM-5/MCM-41 Composite Zeolite
- Near Net Shape Forming Process of a Titanium Alloy Component Using Hot Isostatic Pressing with Graphite Mould
- Nitrogen Doping Effects on Microstructure of Multi-Walled Carbon Nanotubes
- Research on Feasibility and Applicability of Delamination Localization Methods for Composite Laminated Beams
- Side Effects on Enhancing Chemical Herbicides to Control Proposal
- Simulation Research on Optical Performance of Multicrystalline Silicon Texture Structure
- Strengthen of Mechanism of 30CrMnSiNi2A Steel Welded Joint with Ultrasonic Impact Treatment
- Study on Ball Milling of TiH2 and Application in Energetic Materials
- Study on Corrosion Damage Rule for Two Type of Aluminum Alloy
- Study on Features and Application of Typical Smart Materials
- Study on Nanometer ATO Powder Prepared with Citric Acid as Dispersant and its Conductive Properties
- Surface Modification on Rabbit Hair Fiber for Anti-Static and Ultraviolet Protective Properties via ZnO Nanopartciles
- Synergistic Effects of a Red Phosphorus Master Batch on a Modified Intumescent Flame Retardant ABS Composites
- Synergistic Flame Retardant Effect of Fumed Silica and Zinc Borate with Magnesium Hydroxide in ABS Based Flame Retardant Composites
- Texture Evolution of Friction-Stir-Welded 5A30 Aluminum Alloy Plate
- The Aging Properties of Bamboo-Poplar Composite Oriented Strand Board with Different Hybrid Ratios
- The Development of Double Composite Flexible Radar Absorbing Fabrics Based on Iron Fibers
- The Discussion about Concrete on the Relationship between Corrosion Resistance and Time under Bending Loads
- The Friction and Wear Properties of Cu-Te-Li Alloys with High-Strength and High-Conductivity
- The Range Distribution of Yb Ions Implanted in 6H Silicon Carbide
- Ultrasonic Inspection for Metal Creep Based on Flight-Time-Attenuation
- Corrosion Behavior of Titanium Alloy and Titanium in Different Solution
- The Analysis of Temperature Field of Concrete Beam of Hydration Heat
- Effect of Fumed Silica and Zinc Borate on the Thermogravimetric Analysis Curves of ABS/Magnesium Hydroxide Composite
- Analysis the Machined Surface Quality during the Drilling of Steel X04Cr16Ni12MnTiN
- Double Sided Explosive Cladding of Stainless Steel and Regular Steel
- The Influence of Particle Diameter on Analytical Results
- Experiment Research of Laser Induced Air Breakdown
- Chapter 2: Applied Mechanics, Design, Simulation and Manufacturing
- A Study of Simulation of Hydropreumatic Suspension Experiment Rig Based on AMESim and Matlab/Simulink
- 90W Off-Line High Power Factor Correction Module Design
- Applications of the Photothermal Cohesion Technology in the Fresh Air System and Air Purification Devices
- Based on Rub a Drum Machine Four-Axis Machining Fixture Design and Modeling in Solidworks and Virtual Assembly
- Based on Solidworks and Mastercam Combined for Rub a Drum of Four-Axis NC Machining Programming Research
- Cavitation Effect to the Hydraulic Piston Pump Flow Pulsation
- Comparison of the Load with Different Loading Ways in the Finite Element Model of the Mobile Air Compressor Frame
- Deformation Analysis of Dam with the Improved Wavelet Threshold
- Design and Analysis of a Novel Micro Flying Head in Mass Storage System
- Design and Optimize the Branch Pattern of Herringbone Well
- Design and Simulation for Braking System of FSAE Racing Car
- Design and Simulation of a Descent Control Device Based on Hydraulic Damping
- Design of a Type of Lift Coating Machine
- Design of Injection Mould for the Special-Shaped Claw Cover of an Automatic Breast Pump and Milking Machine
- Design of Testbed for Feel Simulator of Battleplan
- Development of Hole-Based Self-Centering Marking Gauge
- Development of the Assistant Positioning Device of Parallel Machine Vice
- Disk Cam Contour Design Based on Inventor 2009
- Dynamic Modeling of Shaking Table Based on Simulink/SimMechanics
- Dynamics Analysis of a 3-DOF Parallel Mechanism
- Effect of the Rudder on the Vibration Frequency of Wind Turbine
- Electromagnetic Simulation and Dynamic Analysis about the Electromagnetic Propelling System of Magnetic Suspension Launcher
- Fault Diagnosis Approach for Incipient Bearing Fault in Wind Turbine under Variable Conditions
- Finite Element Analysis and Experimental Research for Horizontal Tank to Internal Magnetic Flux Leakage Detection
- Hardware Design of Automotive Parking Heater Remoter and Receiver
- Heavy Duty Automobile Self-Discharging Hydraulic System Design
- Horizontal Well Fracturing Optimization Numerical Simulation
- Hydraulic Excavator Boom Lightweight Design
- Intensive CNC Machine Programming with Circular Pattern Algorithm
- Machine Gun Finite Element Model Amending Based on Frequency Response Functions of Vibration
- Modeling and Simulation of Turbofan Engine Based on Modularized Subassembly
- Modular Design Technology of Multi-DOF Mechanical Arm
- Multi-Objective Collaborative Optimization of Spring
- Numerical Investigation of Tip Clearance Flow in an Axial Compressor Cascade
- Numerical Simulation of the Shell Fragments Damage-Field Based on ANSYS/LS-DYNA
- Numerical Simulation Research of Air-Assisted Atomizer Internal Gas Flow Field Based on Fluent
- Parametric Design of Tapered End Mills with Variable Pitch for Improving Stability
- Permeability Improvement Technology of Directional Hydraulic Fracturing in Low Permeability
- Pre-Deformed Design of Optical Lenses with Reverse Engineering and Virtual Manufacturing
- Research and Development of a Knowledge-Based System for Blanking Die
- Research on Attitude Singularity Problem of Small Tail-Sitter Aircraft
- Research on CNC Machining System of Directly Driven by Image Based on PMAC
- Research on Influence Factors of Landing Gear Retractile Hydraulic System Performance Degradation
- Research on the Forming Path for Fabricating the Sheet-Metal Part with Non-Horizontal End Face Using CNC Incremental Forming
- Research on the Simulation of NC Milling Program Based on VERICUT Oriented to the Five-Axis Micro-Milling System
- Research on the Stress Uniformity of the High Speed Bearing with Heavy Load in Cold Rolling
- Research on Typical Vibration Accelerations of Wind Wheel Changing with Yaw Angle
- Rolling Bearing Feature Extraction Based on Wavelet Filtering with Optimal Combination Bands
- Second-Order Two-Scale Asymptotic Expansions for Thermopiezoelectric Problems in Periodic Structure
- Simulation and Design of Portable Underwater Acoustic Transducer Test Device
- Simulation and Optimization Design of Gasoline Engine Exhaust Muffler
- Simulation and Optimization for the Cooling System of Heavy Vehicle Engine
- Simulation and Parameter Design of a 10kw Wireless Power Transfer System Applied to Gantry Crane
- Simulation and Test Study of Multidisc Magneto-Rheological Fluid Clutch
- Simulation Study on a Parallel Hybrid System of Hydraulic Excavator
- Structural Optimization of Drilling Bed for Deep Hole Drilling Machine
- Study on Influence of End Concavity of Rolled Piece by Billet Circular Arc Angle with CWR
- Study on Split-Open Loading in V-Shaped Components Forming Process
- Study on the Welding of Feeder Hopper and Cylinder Instead of Casting Process
- The Design of the Fixture for the Thin Wall Cone Parts
- The Design of Wave Height Standard Device in the WTTVS and its Error Analysis
- The Design Research on the Key Components of Low-Speed Marine Diesel Engine
- The Forced Response Analysis of Heavy Duty Vehicle’s Cab
- The Nanocutting by Rigid/Elastic Tools with Nose Radius at the Gas Environment Using Molecular Dynamics Simulations
- The Optimal Design for Ring Blank Dimensions in Inner L-Shaped Ring Rolling Process
- The Parametric Design and Simulation for Globoidal Indexing Cam Mechanism
- The Research of New Rings Process of Casting-Rolling Continuously Forming
- Thermal Deformation Analysis of a Magnetic Climbing Wall Car Frame Based on the ANSYS
- UML Based Design Approach for Storage System of Nano-Satellite
- Biomechanical Analysis of Typical Upper Limb Movements Based on Kinect-LifeMOD
- Dynamics Simulation Research of Planar Four-Bar Mechanism with Multi-Joint Clearance
- Data Flow Analysis on 3D Printing for Distributed Manufacturing Information System
- Modal Analysis Based on Finite Element Jaw Crusher Rotor
- The Dynamic Strength Calculation on the Reel Fulcrum of Crane Based on ADAMS and FEA
- Surface Waviness in Abrasive Waterjet Offset-Mode Turning
- Develop the System of Three Dimensional Parametric Design of Planetary Gear Reducer Parts Library Base on CS Structure
- Optimization Design of Hot Runner Injection Molding for Thin Shell Parts Based on Moldflow
- Parameter Identification of a Plastic Damage Model
- Research on the Molding Condition of 3D Braided Nozzle Throat Fabric
- Stress Analysis for Globoidal Indexing Cam Mechanism with Steel Ball
- Stress Forming of Fine Metal Wire Based on Ultrasonic Vibration
- Study on Bladder Forming of the Shallow Basin-Shaped Aluminum Sheet Parts
- Multi-Type of Generators Scheduling Optimization Model Based on LHS Method and the Mean-CVaR Model
- Research on the Common Rail Transport System Building in Integration System of Urban Rail Transit in Hohhot
- Numerical Investigation of Choking Cavitator Based on Orthogonal Experiment
- Research on One Kind of Intellectualization High Accuracy Digital Adjustment Direct Source
- An Inquiry into the Sustainable Development of Cellulosic Ethanol in Tianjin, China
- Main Technologies of Life Support System of Evacuated Tube Transportation Vehicle Passenger Cabin
- Modeling and Predicting Surface Roughness for the Grinding Process
- A Band-Gap Voltage Reference for LDO Circuit
- A Photovoltaic Soft Switching Boost Circuit
- Calculate Formation Velocity from Vertical Seismic Profiling Data
- Design of a 10MPa Nanosecond Gas Switch with Adjustable Gap
- HMI Design of Lead-Acid Battery Retreading System Based on DWIN DGUS Screen
- Key Technologies of Rigid-Flexible Coupling System Modeling and Simulation
- Research Method and Key Design Themes of a Multifunctional Jacket with Optoelectronic Effects
- Design, Fabrication and Evaluation of a Multifunctional Jacket with Optoelectronic Effects
- Chapter 3: Measurement, Monitoring, Control and Testing Technologies
- A Certain Type of Artillery Open Loop Servo System Reform Research Allocation Zoom Multiples
- A Control System on Soil Temperature
- A Method of Coordinate Measuring Path Planning Based on Polychromatic Sets
- A Novel Optical Fiber Displacement Measurement System
- 100MHz to 2.5GHz RF Detector Based on SiGe HBT
- A Kind of Online Insulation and Error Online Monitoring Technique
- A Method of Correcting Brightness Gradient in Thermal Infrared Image
- A Method of Full Digital Clock Generation with Adjustable Frequency and Phase
- The Factors Influencing the Surface Quality of Machining and Improving Measures
- The Intelligent Traffic Monitoring System Based on Beidou Research and Design
- The Model Establishment and Simulation Analysis of Controllable Pendulum
- The Number of Runs and its Application in Biological Medicine Testing
- The Optimized Design of Coordinated Control System Based on Load Feedforward and Unidirectional Decoupling
- The Research of Network Intrusion Detection Technology Based on Genetic Algorithm and BP Neural Network
- The Research of Radio Monitoring System for Army Digital Force Training
- The Research of Self-Balancing Vehicle Based on Posture Sensor System
- The Resulting Toolpath of Turning a Special Surface on CNC Lathe
- The Simulation about Single-Phase Bridge Type all Control the Rectifier Circuit is Based on Matlab
- The Study on Voltage Control Based on MAS and Grid Technology
- Theoretical Study on Bridge Structure Condition Evaluation Based on Health Monitoring Data
- Transient Stability of Power System Based on Multi-Agent System
- Vehicle Trajectory Prediction Based on Road Recognition
- Waveform Measurement and Analysis of Common Household Appliances
- A Novel of L-Serine/Chitosan Electrochemical Sensor for Determination of Paracetamol
- A Practical Signal Progressing Method for Magnetic Flux Leakage Testing
- A Single-Cell Replacement Strategy on Electronic Array Self-Healing
- A Survey on Moving Target Tracking in the Intelligent Visual Monitoring System
- Adaptive Fuzzy PID Control Applied in Boiler System of Power Plant
- An Approach for Detecting Illegal Load in Wireless Power Transfer System
- An Image Positioning Method of Automatic Random Walker Based on IFS Edge Detection
- An Improved Adaboost Method for Face Detection
- An Improved Algorithm for Real-Time Moving Target Detection Based on Gaussian Mixture Model
- Analysis and Research of Rogowski Coil Current Sensing Technology
- Analysis of Air Power Switch Work under Harmonic
- Application of BP Neural Network PID Algorithm in Refrigerated Space Temperature Control
- Application of Parameter-Adaptative Fuzzy PID Control in the Temperature Control System for Liquor Filling and Sealing Machine
- Approach to Design Digital Meter for Monitoring Armored Vehicle Engine
- Auto Disturbance Rejection Control Strategy for Large Inertia Servo System
- Automatic Test and Fault Diagnosing System of XX Airborne Navigation and Control System
- Based on Energy-Efficient Opportunistic Multicast Routing for Mobile Wireless Sensor Networks
- Critical Event-Triggered Transmission for Wireless Sensor Node in Aircraft Structural Health Monitoring
- Design and Analysis of Dual Hall Position Sensor with Automatic Direction Recognizing and Pre-Positioning Function
- Design and Analysis on the Anti-Lock Braking Control System of a Four-Wheel Vehicle
- Design for Speed Measuring of Railway Crossing Based on Track Circuit
- Design of a Fast Resistance Sorting Instrument Based on STC Microcontroller
- Design of a Temporary Ground Wire Monitoring System and Reliability Research
- Design of a Two Levels Self-Integrating Capacitive Divider
- Design of Automatic Milking Controller
- Design of Digital Type Axis-Angle Sensor Based on Singlechip
- Design of Plunger Limit Switch Testing System Based on Virtual Instrument Technology
- Design of the IDCTMV Human-Machine Ergonomics Test System
- Design of the Target Tracking Process Based on DM648
- Development of Experimental Apparatus for Diaphragm Gas Meter in the Limiting Temperature Conditions
- Development of the Portable Field First-Aid Diagnosis Bed
- Diesel Engine Inlet and Exhaust System Fault Detection Based on PSO-BP NN
- Effects of Quay Wall and Seabed Reflection on the AUV Acoustic Radiation Test Analysis
- Empirical Likelihood Based Testing for Polynomial Regression Models
- Experimental Study on the Emergency Ampacity of XLPE Cable and its Application
- Experiments and Analyses of Horizontal Earth Electrodes’ TGR on Various Grounds
- Finite Element Analysis of Capacitance Sensor
- FPGA-Based High Precision Illumination Measurement System: A Prototype Development and Evaluation
- Frequency Control QPSK Modulator Based on DDS Technology
- Fuzzy Neural Network Based on Genetic Algorithm for Temperature Control of Variable Air Volume Air Conditioning
- Hybrid Base and Parallel Hybrid Electric Vehicle Control Strategy
- Improvement of Stable Operation Ability for Large-Scale Wind Power System Based on VSC-HVDC Technology
- Initial Orbit Determination Using Single Frequency GPS Measurements of Launch Vehicle
- In Situ Tester Research and Development of Control Stick Force Sensor
- Laser-Welding Spots Detection Based on Original Moment Values
- Many High Performance Motion Control of Linear Motor Drive System Research
- Modal Hammering Test and Sensitivity Analysis for BIW Vehicle
- Modeling Analysis and Experimental Study of Circular Piezoelectric Unimorph Actuator
- New Method of Angle Error Measurement in Angular Artifacts Using Minimum Zone Flatness Plane
- Nondestructive Testing Methods of Coating Performance
- Offset Error Research of Self-Triggering Pulsed Mini Laser Radar System
- Ontology and Multi-Agent Based Intelligent Retrieval Model for Power Quality Monitoring Information
- Optimization of Reliability Test on the Shell of Portable Electronic Products Based on Taguchi Method
- Research and Application on Intrusion Detection Technology Based on Improved BM Algorithm
- Research and Design of Touch-Screen Domestic Universal Remote Controller with Self-Learning Function
- Research on Active Online Diagnosis Technology of Hydraulic System
- Research on Data Acquisition Technology of Wind Turbine Monitoring System
- Research on Key Techniques of Multi-Sensor Intelligent Video Surveillance System
- Research on Test Technology of Remote Weapon Station’s Dynamic Parameter
- Research on the Pattern of Boom-Type Roadheader Intelligent Control System
- Research on the Simulation Design System of Indoor Precise Control Field Based on VRML
- Research on the Technology of Middleware of Distributed Spectrum Monitoring System
- Simulation of Magnetically Controlled Reactors Based on MATLAB
- Splitting Strength Detection Test of Shallow Asphalt Pavement and Master Curve of Splitting Strength
- Study on Intelligent Anti-Theft Alarm System of Power Transformer
- Synchronization Control Scheme for Antenna Pointing Control System Based on Hybrid Linear Actuator
- Test and Analysis of Dynamic Characteristics of Reinforced Concrete Arch Bridge
- Testing Research of Fiber Bragg Grating Strain Sensor Embedded in Bored Pile
- The Application of PSO-BP Neural Network PID Controller in Variable Frequency Speed Regulation System
- The Construction Quality Control Measures of Reinforced Concrete Cover Research
- The Design and Simulation of Scheelite Alkali Autoclave Reactor Fuzzy-PID Controller
- The Design of Automatic Remote Monitoring System for the Temperature and Humidity Based on GPRS
- The Design of Communication System for Wearable Health Monitoring Equipment
- The Design of Greenhouse Temperature Control System
- The Design of Landslide Hazard Remote Monitoring System Based on STM32 MCU and GPRS
- The Development of an Automatic Ultrasonic Non-Destructive Testing System
- Design of Temperature Control System Based on FPGA and Fuzzy-PID Control Algorithm
- Development of Two-Dimensional Motion Platform Control System Based on xPC Target
- Research on PVDF Micro-Force Sensor
- Sound Recognition Algorithm for Power Devices Based on Substation Inspection Robots
- Static Characteristic Test of High Temperature Pressure Sensor
- The Characteristics of Dyed Fancy Yarn Formation Pattern Research
- The Measurement of Concrete Temperature Distribution Based on VB
- An Intelligent Traffic Signal Controller Based on CAN Bus
- Introduction to Computers in the Mechanical and Electrical Control is Widely Used in the Field of Industry
- Long-Endurance Multi-Function Floating Platform
- A Fast Pose Estimation Method of Four-Rotor Aircraft
- Research of Small Current Grounding Fault Classification Based on Phase Plane Method
- A Kind of Portable Wire Rope Testing Equipment
- Blind Pipe Type Fiber Bragg Grating Hydrostatic Gauge
- Research on the Detection of Focusing Mechanisms
- Design of Programmed Temperature Control Gas-Sensing Characteristic Tester
- Development of Automatic CNC Grooving and Bending Machine Based on MPC08SP Motion Control Card
- Research on XCTD Launcher Based on EML Technology
- Scanning Mirror Topology Optimization of the Imaging Spectrometer
- Development of the Comprehensive Performance Test Equipment of the Electromagnetic Switch on Automobile Starter
- Dynamic Matrix Control for Multiple Gas Collectors of Coke Ovens
- Effect of Vehicle Speed on Contact Pressure and Current Collecting Quality
- Gear Fault Signal Modeling Study Based on Probability Box Theory
- 5T Information Fusion System Based on Train Technology Scheme Design
- Prediction of PAHs Emitted from Marine Diesel Engine Using Artificial Neural Networks Combining Genetic Algorithms
- Research on Flood Control Operation for Poyang Lake Semi-Restoration Dikes are Based on Variable Fuzzy Optimization Theory
- Research on Reliability Allocation Method for NC Grinding Machine
- Selection of Plate Self-Locking Nut
- Study on Automobile Intelligent Automatic Clutch System
- Study on Simulation of Aircraft Background Magnetic Field
- Computer Modal Analysis of the Two-Dimensional Precision Turntable
- The Electrical Standard Practices in the Role of Airbus Aircraft Maintenance
- Application of Inverse Distance Weighted Interpolation Method in Finite Temperature Point Temperature Field
- The Localization Method of ALV Based on Lateral Dynamics
- The Path Recognition Method of Smart Car Based on Linear CCD
- Soft-Starting Method Analysis of Belt Conveyor
- The Tool Setting Skills of Round Parts in NC Milling
- Research of Tracking and Prediction of Moving Object with Kalman
- A Four-Coordinate CNC Device Based on Engraving and Milling Machine
- Chapter 4: Communication and Navigation, Information Technologies, Algorithms and Numerical Methods, Image, Video, Signal and Data Processing
- Design and Research of Biological Information Based on the Signal Extraction Algorithm
- A GIS and Web-Based Decision Support System for Regional Water Resource Management and Planning
- A New Numerical Scheme for the Space Fractional Diffusion Equation
- A Class of Difference Inequality with Three Iterative Summation
- A Degree Distribution Optimization Algorithm in Unequal-Protected LT Code
- A Fast PSF Calibration Method for Single Lens Imaging
- A Method for Analyzing Clinical Heart Sound Signal Based on Chaotic Characteristics
- A Method for Software-Related Safety-Critical Scenarios Identification
- A New Auto-Extraction Algorithm of Lunar Craters for Chang’E Data Based on the Solar Incidence Angle
- A New Auto-Extraction Algorithm of Multi-Size Lunar Craters Based on the Chang’E Data
- A New Method for Code Optimization
- A New Rough Set Model and its Application
- A Novel Blind Source Separation Algorithm for Linear Mixture Signals
- A Novel Distribution Parameter Fitting Algorithm of Correlation Noise Model for Distributed Video Coding
- A Novel Method of Spike Detection for Interferograms Based on Two-Step Filtering
- A Novel Overlapping Community Detection Algorithm of Weighted Networks
- An Assessment Method of the Data Similarity Considering the Shape Differences of Objects
- An Improved Decision Strategy of Network Routing Based on Ant Colony Algorithm
- An Improved Error Concealment Technique Based on Multi-View Video Coding
- An Improved Frame Loss Concealment Algorithm Based on the Mixed Excitation Linear Prediction
- Analysis and Simulations of Lensless Imaging with Intensity Correlation Method
- Analysis of Black Level Calibration Algorithm for CIS
- Application Demand Analysis of Message-Oriented Middleware with Pub/Sub Model on TT&C Computer
- Application of C Sharp and MATLAB Mixed Programming Based on .Net Assembly in Blind Source Separation
- Bayesian Compressive Sensing of Images Based on Effective Blocking
- Campus Tracking System Based on IoT
- Candidate Region Detection of Ship Target in Port Based on Electronic Map
- Car Branding and Communication Strategy Research Based on Microblogging
- Characteristic Study on Carrier Communication Device Noise of Low Voltage Power Lines Based on UPS
- Certificateless Multi-Signcryption Scheme without Pairing
- Chinese Short Text Semanteme Analysis and Emotion Value Quantization Algorithm
- Collaborative Filtering Recommendation Technology Based on Genetic Algorithm
- Compressed Sensing Image Reconstruction Based on Improved Particle Swarm Optimization Algorithm
- Computer Network Security Strategy Research
- Construction of Data Association Model in Coal Mines Based on the Application of Internet of Things
- Design and Implementation of FPGA-Based High-Performance Floating Point Arithmetic Unit
- Design of Ultrasonic Rangefinder Controlled by Single Chip Microcomputer
- Detection and Parameter Estimation for Chirp Signal Based on Fractional Fourier Transform
- Detection and Tracking for Anomalous Motion Targets Using Wireless Sensor Networks
- Distance Features of Different Fatigue State
- Early Warning of Power Plant Equipment Based on Massive Real-Time Data Mining Technology
- Efficiency Analysis of Different Cooperative Communication Schemes in Wireless Sensor Networks
- Enumeration of the Generalized Rook Monoid
- ERP Feature of Matching Pennies
- Estimation of Distribution Algorithm using Two Kinds of Information for Solving Knapsack Problem
- Face Recognition Image Processing Design Research
- Fault Prediction Methods Study of Machinery Based on Optimized Background Value MGM(1,m) Model
- Feature Extraction of Underwater Target Ultrasonic Echo Based on Wavelet Transform
- Fusion of Visible and Infrared Images Based on Non-Sampling Contourlet and Wavelet Transform
- GaAs MMIC Wideband SP8T Switch
- Hardware Design of Track Circuit in Rail Transit Test System Based on ICL8038
- HD Video Online Recognition Based on DCT Spread Spectrum Watermarking Algorithm
- Holography Reconstruction of the AUV Radiated Acoustic Field and the Influencing Factors Analysis
- Image Processing and Sparse Resolution for Underwater Imaging
- Implementation of CRC in 10-Gigabit Ethernet Based on FPGA
- Improvement of K-Anonymity Location Privacy Protection Algorithm Based on Hierarchy Clustering
- Mobile Learning Mode Based on 3G
- Modeling and Analyzing of RRC Protocol Process Based on CPN
- Motion Comparison Method Combining Segmented Multi-Joint Line Graphs with the SIFT Matching Technique
- Multi-Channel MKL for Video Human Action Recognition
- Network Equipment Selection Scheme of University Informatization Construction
- New Data Processing Method Research on GLONASS
- Optimal Path Planning of Beidou Navigation System Based on Dijkstra Algorithm
- Parameter Estimation of Nonlinear Muskingum Models Based on OEPSO
- Prediction of Road Congestion Level Based on Bayes Algorithm
- Real Time Message Matching Algorithm for Message-Oriented Middleware with Pub/Sub Model on TT&C Computer
- Receive and Display Beidou Positioning Information Based on MapX
- Recurrence Characteristics Analysis of Near-Surface Wind Speed Signal with Different Sampling Frequencies
- Research and Simulation of LCMV Algorithm in GNSS Anti-Interference
- Research of an IPSec VPN Application in Enterprise Network
- Research of LXI Discovery Method
- Research of Text Recognition Based on Natural Scene
- Research of Weapon Training Simulator Software Model Based on UML
- Research on Combined Weight of Target Threat Index of Information Fusion
- Research on Flight Altitude Information Fusion Method for ADS/INS/GPS Integrated Systems Based on Federated Filter
- Research on Information Exchange Platform Based-Web Services for Tourist
- Research on Information Interactive Model of Automated Demand Response
- Research on Limit-Trajectory Over-Modulation Strategy of Two Stage Matrix Converter
- Research on SIFT Matching Algorithm Based on GPU
- Research on Switch Power Module Parallel Operation System
- Research on the Application of Cloud Computing in the Field of Archives Informatization
- Research on the Performance Test of Wired/Wireless Heterogeneous Industrial Control Network
- Research on Vague Set of Target Threat Information Fusion Algorithm
- Research on Wireless Network Traffic Modeling Based on Channel State
- Research on XML Documents and Relational Database Mapping Based on XML Schema
- Simulation of Clouds Dynamics Based on the Change of Sight Distance
- Small Quantities of Cargo Transportation Route Selection Base on Minimum Spanning Tree Algorithm
- Smart Meter Based on Smart Energy Profile for ZigBee and Power Line Communication Connectivity-Enabled Home Area Network
- Software Design for Micromouse Special Navigation
- Software Design for Micromouse Straight Path Navigation
- Solid Rocket Motor Finite Element Analysis Based on the Reverse Modeling of ICT Images
- Solitary Wave Solutions, Periodic Wave Solutions and Folded Localized Excitations for the Dissipative Zabolotskaya-Khokhlov System
- Speaker Recognition Techniques
- Study of Archives Information Development Based on SWOT Analysis
- Study of Steady-State Kalman Filtering Based on Thresholding Optimal Gain
- Study of the Simultaneous Generation of UWB Doublet and Triplet Signals Based on Nonlinear Effects of SOA
- Study on Synthetic Aperture Radar Image Denoising Algorithm
- Study on the Method of Vibration Signal De-Noising Using Wavelet Packet Based on QPSO
- Summary and Expectation of Synthetic Aperture Imaging towards High-Orbit Objects
- Text Clustering Algorithm of Co-Occurrence Word Based on Association-Rule Mining
- The Analysis of Steganographic by Sub-Pixel Calibration
- The Combination Views of Privacy-Protection in the Mobile Database
- The Design and Realize on the Circuit Board of High-Speed Image Acquisition System
- The Differences Analysis of Input-Output Efficiency of Regional R&D Activities Based on DEA
- The Exploration and Implementation of the Interactive Multimedia Network Autonomous Learning Platform
- The Optimization and Application of Kriging Model Based on Quantum-Behaved Particle Swarm Optimization
- The Solution to Node Importance in Complex Networks Based on PageRank Algorithm
- The Study of a Fingerprint Encryption Code Model
- The Study of Harmonic Suppression and Reactive Power Compensation
- The SWOT Analysis of the Application of Cloud Computing to Archives Informatization
- Topological Structure - Based Rough Sets and Rough Logic
- Ultra-Low Frequency Difference Signal Multiplication Based on PLL
- Uncertainty Evaluation of Duration of Aircraft DC Transient Signal Based on Least Square Method
- University Employment Information Integration Model Based on Cloud Computing
- Wavelet-Based Adaptive Detection of Magnetic Anomaly Signal Contaminated by 1/f Noise
- Weakness and Improvement of an Efficient Key Agreement Protocol
- Wideband SPDT Switch With TTL Control
- Comparison and Improvements of Feature Extraction Methods for Text Categorization
- A Discriminative Method for Pedestrians Detection on Real-Time Video
- Research on the Iterative Stopping Criterion Based on Linear Turbo Equalization
- Big Data Reasearch on Smart Phone Unlock Crack
- Corneal Image Analysis and Information Management System Based on Slit Lamp
- Design and Implement of a Computer Forensics Model for Cloud Environments
- Design of Wave/Tide Simulate Apparatus’ Control Software Based on Free Port Communication Protocol
- Image Decomposition and Inpainting Based on Besov and Hilbert-Sobolev Space
- iMRAproiri: A Parallel Aproiri Algorithm Based on Twister
- Research on Industrial Control Network Webstation Design
- Research on Bandwidth Allocation of Multimedia Communication System Based on Internet of Things
- Research on Design of Network Curriculum
- Information Communication Technology Applications for World Heritage Site Management
- The Diagnosis Research of Cover Sheet Spring Recover on the Compensate Fuzzy Nerve Net of Multi-Input Defer
- The Performance Evaluation of the External Effect of Regional Logistics Information Platform
- Novel Algorithm for Calibrating Speed-Density Model Parameters in Mesoscopic Traffic Simulator
- Design and Realization of Collaborative Simulation on VRNET and VR-Forces Cross Platform
- Optimization of Maintenance Equipment Tool Types Based on Triangle Fuzzy Number
- System Mechanism of Small IOT System - Taking the Openhab Project as an Example
- The Application of Tolerance Database in the Secondary Development of SolidWorks
- A Novel Cluster Selection Algorithm in the NIDS of Wireless Ad Hoc
- A Novel Nonlinear Time Series Prediction Method and its Application in Structural Vibration Response Prediction
- A Solution of Designing Remote Video Conferences Based on ARM11
- Analysis and Simulation to the Anti-Jamming Performance of the CCSK Soft Spread Spectrum System
- Consensus Analysis for a Class of Heterogeneous Multi-Agent Systems in Directed Graph
- The Application of Multimedia Video Technology in 3D Table Tennis Games
- Optimal Power Flow Solution Using the Harmony Search Algorithm
- Power Harmonic Analysis System Based on Virtual Instrument
- Reconfigurable Virtual Instrument Test System Research Based on Mobile Platform
- Replacement of the Power Generation Unit and Benefit Allocation Model Based on the Power Generation Performance
- Research and Improvement about LEACH Algorithm for Wireless Sensor Networks
- Research on Diffuse Optical Tomography System in Frequency Domain
- Research on Remote Sensing Image Geometric Correction Method and Precision Analysis
- Short-Term Wind Speed Prediction on Base of Improved Least Squares Support Vector Machine
- Study of Convective Heat Transfer Coefficient of High Pressure Water Descaling
- Study on Flood-Fill Algorithm Used in Micromouse Solving Maze
- Study on the Wrapping Error of GREEN’s Function Sampled in K Space
- Status and Prospect of Disassembly Process of Electronic Components on Waste PCBs
- Getting the Health Management Information System Building
- Analysis for Position Selection of Hinged Point in a Forestry Transportation Articulated Vehicle
- Chapter 5: New Technologies in Education and Sports
- Research of the Experimental Teaching about IPSec Protocol Based on Transport Pattern
- Research on Practice Teaching of Civil Engineering on the Basis of the Student Competition
- Cross-Cultural Awareness in College English Teaching
- Research on “Two Labs and Two Centers” Art and Design Practice Teaching Mode
- Study on Students’ Network Moral Education
- The Application of Information Technology in the Fine Arts Teaching and Implementation
- The Economic Analysis on the Special Education Teachers in Human Capital
- The Innovation of the Construction of Style of Study of Connotative Development of Higher Education
- The Research on the Core System of Athletics
- Discussion on Research Learning under the Network Environment
- Research and Practice of Teaching Reform of Wireless Network Technology Course for Internet of Things Specialty
- Research on the Reform of Metallurgical Engineering Practice Teaching
- Study on the Cultural Construction of College Archives
- On the Design and Development of Micro-Course
- The Design and Realization of Online Submitted System of Graduation Design Documents
- Chapter 6: Management Engineering, Business and Economics Engineering
- An Investigation of Electronic Logistics Management in the Taiwanese Textile Industry: Using Everest Textile as an Example
- Analyses the Mechanical Equipment Management and Maintenance
- Application of Lean Quality Management in Heat Treatment Industry - An Example of Enterprise N
- A Modified Exponential Smoothing Model for Forecasting Per Capita GDP in Yunnan Minority Area
- A Study on CPFR Inventory Management Technology
- A Traffic Capacity Model of Lane Occupation
- An Empirical Study on Exponential Smoothing and Seasonal Model
- Based on Geographic Information System of Tourism Resources and Circuit Management System Design and Implementation
- Design and Implementation of Room Management System of Hotel Based on J2EE
- Design and Implementation of Storage Management System Based on Java
- Design and Implementation of University Administrative Management System
- Design of Prognostics and Health Management System for Turbofan Engine
- Fuzzy Comprehensive Evaluation on Human Resource Management Risk Warning Model
- Material Selection and Management Based on Cybernetics
- Research on Episode Segmentation for MIS Workflow
- Research on Purchase Intention Models of Seamless Underwear Consumers
- Risk Assessment and Countermeasures of Occupational Fraud Conduct in Corporate Construction Projects
- Team Organization Model and its Algorithm for a Project under Complex Constraints
- The Comparative Study on Urban Transport and Urban Agglomeration Transport
- The Theory of Economic Law to the Construction of Harmonious Society in our Country Value Analysis
- The Urban and Rural Public Transit Demand Analysis in Hohhot
- University Personnel Management System Construction and Implementation
- Design Research on Computer Logistics Information Management System
- Economic Analysis on Space Truss Structure under Different Specific Conditions
- Research of the Store Image Based on Wechat Public Platform
- Stakeholder Analysis of EV Spread in China
- The Background and the International and Domestic Impact of 'General Data Protection Regulation'
- The Design and Application of All-Areas and Best Traversal Algorithm Based on Uniform Points on Scene Check
- The Legislative Reference on Software Vulnerability of Foreign Critical Infrastructure
- Bound of Local Risk Minimization Estimation on gλSpace
- Computer Database System in the Application of Information Management
- The Library Information Management System Analysis and Design
- Modeling the Influence of Design Modification on Product Development Projects Based on Structure Methods
- Theoretical Framework for Innovation Design with Optimised Customization
- Research of State Assessment for UAV Based on FAHP
- The Design of Operation and Maintenance Management System about IT Platform Based on Tivoli
- Simulation Modeling of Post-Earthquake Vaccine Cold-Chain Emergency Transportation Based on ExtendSim
Les mer
Produktdetaljer
ISBN
9783038351924
Publisert
2014-10-01
Utgiver
Trans Tech Publications Ltd; Trans Tech Publications Ltd
Vekt
4430 gr
Høyde
240 mm
Bredde
170 mm
Dybde
119 mm
Aldersnivå
P, 06
Språk
Product language
Engelsk
Format
Product format
Heftet
Antall sider
2376